LPC1113FHN33 NXP Semiconductors, LPC1113FHN33 Datasheet - Page 38

The LPC1113FHN33 is an ARM Cortex-M0 microcontroller and it can operate up to 50 MHz

LPC1113FHN33

Manufacturer Part Number
LPC1113FHN33
Description
The LPC1113FHN33 is an ARM Cortex-M0 microcontroller and it can operate up to 50 MHz
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC1113FHN33
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC1113FHN33
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FHN33/201
Manufacturer:
ON
Quantity:
17
Part Number:
LPC1113FHN33/301
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC1113FHN33/301
Manufacturer:
NXP
Quantity:
2 000
Part Number:
LPC1113FHN33/301
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FHN33/302
Manufacturer:
NXP
Quantity:
308
NXP Semiconductors
Table 12.
[1]
[2]
[3]
[4]
[5]
[6]
LPC111X
Product data sheet
Symbol
V
XTALIN
XTALOUT
V
DD
SS
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to full V
IA = inactive, no pull-up/down enabled.
See
reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down
mode.
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see
I
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
2
C-bus pads compliant with the I
Figure 46
LPC1100XL series: LPC1111/12/13/14 pin description table (HVQFN33 package)
for the reset pad configuration. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to
Pin
6; 29 -
4
5
33
[6]
[6]
Start
logic
input
-
-
-
2
C-bus specification for I
Type Reset
I
I
O
-
All information provided in this document is subject to legal disclaimers.
state
[1]
-
-
-
-
Rev. 7 — 1 March 2012
Description
3.3 V supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
Input to the oscillator circuit and internal clock generator circuits. Input
voltage must not exceed 1.8 V.
Output from the oscillator amplifier.
Thermal pad. Connect to ground.
2
C standard mode and I
LPC1110/11/12/13/14/15
2
C Fast-mode Plus.
32-bit ARM Cortex-M0 microcontroller
…continued
Figure
DD
© NXP B.V. 2012. All rights reserved.
45).
level (V
DD
Figure
= 3.3 V));
38 of 103
45).

Related parts for LPC1113FHN33