SAM3A8C Atmel Corporation, SAM3A8C Datasheet - Page 1213
SAM3A8C
Manufacturer Part Number
SAM3A8C
Description
Manufacturer
Atmel Corporation
- Current page: 1213 of 1465
- Download datasheet (26Mb)
40.7.4
40.7.4.1
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
CAN 2.0 Standard Features
CAN Bit Timing Configuration
All controllers on a CAN bus must have the same bit rate and bit length. At different clock fre-
quencies of the individual controllers, the bit rate has to be adjusted by the time segments.
The CAN protocol specification partitions the nominal bit time into four different segments:
Figure 40-4. Partition of the CAN Bit Time
The TIME QUANTUM (TQ) is a fixed unit of time derived from the MCK period. The total number
of TIME QUANTA in a bit time is programmable from 8 to 25.
SYNC SEG: SYNChronization Segment.
This part of the bit time is used to synchronize the various nodes on the bus. An edge is
expected to lie within this segment. It is 1 TQ long.
This part of the bit time is used to compensate for the physical delay times within the network. It
is twice the sum of the signal’s propagation time on the bus line, the input comparator delay, and
the output driver delay. It is programmable to be 1,2,..., 8 TQ long.
This parameter is defined in the PROPAG field of the
The Phase-Buffer-Segments are used to compensate for edge phase errors. These segments
can be lengthened (PHASE SEG1) or shortened (PHASE SEG2) by resynchronization.
Phase Segment 1 is programmable to be 1,2,..., 8 TQ long.
Phase Segment 2 length has to be at least as long as the Information Processing Time (IPT)
and may not be more than the length of Phase Segment 1.
These parameters are defined in the PHASE1 and PHASE2 fields of the
Register”.
The Information Processing Time (IPT) is the time required for the logic to determine the bit level
of a sampled bit. The IPT begins at the sample point, is measured in TQ and is fixed at 2 TQ for
the Atmel CAN. Since Phase Segment 2 also begins at the sample point and is the last segment
in the bit time, PHASE SEG2 shall not be less than the IPT.
• TIME QUANTUM
• PROP SEG: PROPagation Segment.
• PHASE SEG1, PHASE SEG2: PHASE Segment 1 and 2.
• INFORMATION PROCESSING TIME:
• SAMPLE POINT:
SYNC_SEG
PROP_SEG
NOMINAL BIT TIME
PHASE_SEG1
”CAN Baudrate
Sample Point
PHASE_SEG2
Register”.
SAM3X/A
SAM3X/A
”CAN Baudrate
1213
1213
Related parts for SAM3A8C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: