SAM7S161 Atmel Corporation, SAM7S161 Datasheet - Page 649

• Manufacturer Part Number: SAM7S161
• Manufacturer: Atmel Corporation

Specifications of SAM7S161

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

40.10.5
40.10.5.1
40.10.5.2
40.10.5.3
40.10.6
40.10.6.1
40.10.6.2
6175L–ATARM–28-Jul-11
Parallel Input/Output Controller (PIO)
Power Management Controller (PMC)
PIO: Leakage on PA17 - PA20
PIO: Electrical Characteristics on NRST and PA0-PA16 and PA21-31
PIO: Drive Low NRST, PA0-PA16 and PA21-PA31
PMC: Slow Clock Selected in PMC and a Transition Occurs on PA1
PMC: Programming CSS in PMC_MCKR Register
When PA17, PA18, PA19 or PA20 (the I/O lines multiplexed with the analog inputs) are set as
digital inputs with pull-up disabled, the leakage can be 9 µA in worst case and 90 nA in typical
case per I/O when the I/O is set externally at low level.
Set the I/O to VDDIO by internal or external pull-up.
When NRST or PA0-PA16 or PA21-PA31 are set as digital inputs with pull-up enabled, the volt-
age of the I/O stabilizes at VPull-up.
Vpull-up
This condition causes a leakage through VDDIO. This leakage is 45 µA per pad in worst case at
3.3 V and 25 µA at 1.8V.
I Leakage
It is recommended to use an external pull-up if needed.
When NRST or PA0-PA16 and or PA21-PA31 are set as digital inputs with pull-up enabled, driv-
ing the I/O with an output impedance higher than 500 ohms may not drive the I/O to a logical
zero.
Output impedance must be lower than 500 ohms.
Under certain rare circumstances, when CSS = 00 in PMC_MCKR, and PA1 is set as an input
and a transition occurs on PA1, device malfunction might occur.
Do not transition PA1 as an input when CSS = 00 in PMC_MCKR.
Under certain rare circumstances, reprogramming the CSS value in the PMC_MCKR register
(i.e switching the main clock source) might generate malfunction of the device if the following
two actions occur simultaneously.
VPull-up Min
VDDIO - 0.65 V
Parameter
I Leakage at 3,3V
I Leakage at 1.8V
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
VPull-up Max
VDDIO - 0.45 V
Typ
2.5
1
µA
µA
Max
45
25
µA
µA
SAM7S Series
649