ATtiny24A Atmel Corporation, ATtiny24A Datasheet - Page 106

• Manufacturer Part Number: ATtiny24A
• Manufacturer: Atmel Corporation

Specifications of ATtiny24A

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

12.10.1
12.11 Register Description
12.11.1
106
ATtiny24A/44A/84A
Reusing the Temporary High Byte Register
TCCR1A – Timer/Counter1 Control Register A
Note:
The assembly code example requires that the r17:r16 register pair contains the value to be writ-
ten to TCNT1.
If writing to more than one 16-bit register where the high byte is the same for all registers written,
then the high byte only needs to be written once. However, note that the same rule of atomic
operation described previously also applies in this case.
• Bits 7:6 – COM1A[1:0]: Compare Output Mode for Channel A
• Bits 5:4 – COM1B[1:0]: Compare Output Mode for Channel B
The COM1A[1:0] and COM1B[1:0] control the Output Compare pins (OC1A and OC1B respec-
tively) behavior. If one or both of the COM1A[1:0] bits are written to one, the OC1A output
overrides the normal port functionality of the I/O pin it is connected to. If one or both of the
COM1B[1:0] bit are written to one, the OC1B output overrides the normal port functionality of the
I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit correspond-
ing to the OC1A or OC1B pin must be set in order to enable the output driver.
When the OC1A or OC1B is connected to the pin, the function of the COM1x[1:0] bits is depen-
dent of the WGM1[3:0] bits setting.
Bit
0x2F (0x4F)
Read/Write
Initial Value
C Code Example
void TIM16_WriteTCNT1( unsigned int i )
{
}
unsigned char sreg;
unsigned int i;
/* Save global interrupt flag */
sreg = SREG;
/* Disable interrupts */
_CLI();
/* Set TCNT1 to i */
TCNT1 = i;
/* Restore global interrupt flag */
SREG = sreg;
See
“Code Examples” on page
COM1A1
R/W
7
0
COM1A0
R/W
6
0
COM1B1
R/W
5
0
6.
COM1B0
R/W
4
0
R
3
–
0
R
2
0
–
WGM11
R/W
1
0
WGM10
R/W
0
0
8183D–AVR–04/11
TCCR1A