ATmega644 Atmel Corporation, ATmega644 Datasheet - Page 43

• Manufacturer Part Number: ATmega644
• Manufacturer: Atmel Corporation

Specifications of ATmega644

• Flash (kbytes): 64 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.10.7
8.11
8.11.1
2593N–AVR–07/10
Register Description
On-chip Debug System
SMCR – Sleep Mode Control Register
DIDR0). Refer to
Input Disable Register 0” on page 252
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enters sleep mode,
the main clock source is enabled, and hence, always consumes power. In the deeper sleep
modes, this will contribute significantly to the total current consumption.
There are three alternative ways to disable the OCD system:
• Disable the OCDEN Fuse.
• Disable the JTAGEN Fuse.
• Write one to the JTD bit in MCUCR.
The Sleep Mode Control Register contains control bits for power management.
• Bits 3, 2, 1 – SM2:0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 8-2.
Note:
• Bit 0 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
Bit
0x33 (0x53)
Read/Write
Initial Value
SM2
0
0
0
0
1
1
1
1
1. Standby modes are only recommended for use with external crystals or resonators.
Sleep Mode Select
7
–
R
0
”DIDR1 – Digital Input Disable Register 1” on page 232
SM1
0
0
1
1
0
0
1
1
6
–
R
0
R
5
–
0
SM0
0
1
0
1
0
1
0
1
for details.
R
4
–
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Power-save
Reserved
Reserved
Standby
Extended Standby
SM2
R/W
3
0
(1)
SM1
R/W
2
0
(1)
SM0
R/W
Table
1
0
ATmega644
and
8-2.
”DIDR0 – Digital
R/W
SE
0
0
SMCR
43