AT32UC3B0512 Atmel Corporation, AT32UC3B0512 Datasheet - Page 367

• Manufacturer Part Number: AT32UC3B0512
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

22.7.1.9
32059L–AVR32–01/2012
ID detection
In host mode, the USBSTA.VBUS bit follows an hysteresis based on Session_valid and
Va_Vbus_valid:
The VBus Transition interrupt (VBUSTI) bit in USBSTA is set on each transition of the USB-
STA.VBUS bit.
The USBSTA.VBUS bit is effective whether the USBB is enabled or not.
Figure 22-12 on page 367
Figure 22-12. ID Detection Input Block Diagram
The USB mode (device or host) can be either detected from the USB_ID pin or software
selected by writing to the UIMOD bit, according to the UIDE bit. This allows the USB_ID pin to be
used as a general purpose I/O pin even when the USB interface is enabled.
By default, the USB_ID pin is selected (UIDE is written to one) and the USBB is in device mode
(UBSTA.ID is one), what corresponds to the case where no Mini-A plug is connected, i.e. no
plug or a Mini-B plug is connected and the USB_ID pin is kept high by the internal pull-up resis-
tor from the I/O Controller (which must be enabled if USB_ID is used).
The ID Transition Interrupt (IDTI) bit in USBSTA is set on each transition of the ID bit, i.e. when a
Mini-A plug (host mode) is connected or disconnected. This does not occur when a Mini-B plug
(device mode) is connected or disconnected.
The USBSTA.ID bit is effective whether the USBB is enabled or not.
• It is cleared when the voltage on the VBUS pad is lower than 1.4V.
• It is set when the voltage on the USB_VBUS pad is higher than or equal to 4.4V.
• It is cleared when the voltage on the USB_VBUS pad is lower than 1.4V.
USB_ID
I/O Controller
VDD
shows how the ID transitions are detected.
UIMOD
USBCON
USBCON
1
0
UIDE
USBSTA
ID
USBSTA
IDTI
367