AT32UC3B0512 Atmel Corporation, AT32UC3B0512 Datasheet - Page 246

• Manufacturer Part Number: AT32UC3B0512
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.14.1
Name:
Access:
Offset:
Reset Value: 0x00000000
• SWRST: Software Reset
• SVDIS: TWI Slave Mode Disabled
• SVEN: TWI Slave Mode Enabled
• MSDIS: TWI Master Mode Disabled
• MSEN: TWI Master Mode Enabled
• STOP: Send a STOP Condition
• START: Send a START Condition
32059L–AVR32–01/2012
SWRST
31
23
15
–
–
–
7
0 = No effect.
1 = Equivalent to a system reset.
0 = No effect.
1 = The slave mode is disabled. The shifter and holding characters (if it contains data) are transmitted in case of read operation.
In write operation, the character being transferred must be completely received before disabling.
0 = No effect.
1 = If SVDIS = 0, the slave mode is enabled.
Switching from Master to Slave mode is only permitted when TXCOMP = 1.
0 = No effect.
1 = The master mode is disabled, all pending data is transmitted. The shifter and holding characters (if it contains data) are
transmitted in case of write operation. In read operation, the character being transferred must be completely received before
disabling.
0 = No effect.
1 = If MSDIS = 0, the master mode is enabled.
Switching from Slave to Master mode is only permitted when TXCOMP = 1.
0 = No effect.
1 = STOP Condition is sent just after completing the current byte transmission in master read mode.
0 = No effect.
1 = A frame beginning with a START bit is transmitted according to the features defined in the mode register.
- In single data byte master read, the START and STOP must both be set.
- In multiple data bytes master read, the STOP must be set after the last data received but one.
- In master read mode, if a NACK bit is received, the STOP is automatically performed.
- In multiple data write operation, when both THR and shift register are empty, a STOP condition is automatically sent.
Control Register
CR
Write-only
0x00
30
22
14
–
–
–
6
–
SVDIS
29
21
13
–
–
–
5
SVEN
28
20
12
–
–
–
4
MSDIS
27
19
11
–
–
–
3
MSEN
26
18
10
–
–
–
2
STOP
25
17
–
–
9
–
1
START
24
16
–
–
8
–
0
246