AT32UC3B0512 Atmel Corporation, AT32UC3B0512 Datasheet - Page 243

• Manufacturer Part Number: AT32UC3B0512
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.13.7
19.13.7.1
Figure 19-29. Repeated Start + Reversal from Read to Write Mode
19.13.7.2
Figure 19-30. Repeated Start + Reversal from Write to Read Mode
Notes:
32059L–AVR32–01/2012
TWI_RHR
TWI_RHR
TWI_THR
TWI_THR
TXCOMP
TXCOMP
EOSACC
EOSACC
SVREAD
SVREAD
RXRDY
RXRDY
SVACC
SVACC
TXRDY
TXRDY
TWD
TWD
1. In this case, if THR has not been written at the end of the read command, the clock is automatically stretched before the
Reversal after a Repeated Start
ACK.
Reversal of Read to Write
Reversal of Write to Read
S
S
As soon as a START is detected
As soon as a START is detected
SADR
SADR
The master initiates the communication by a read command and finishes it by a write command.
Figure 19-29 on page 243
Note:
The master initiates the communication by a write command and finishes it by a read com-
mand.Figure 19-30 on page 243
mode.
W
R
Read TWI_RHR
A
A
DATA0
1. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is
detected again.
DATA0
DATA0
A
A
DATA0
DATA1
DATA1
DATA1
describes the repeated start + reversal from Read to Write mode.
NA
A
describes the repeated start + reversal from Write to Read
DATA1
Sr
Sr
SADR
SADR
Cleared after read
Cleared after read
R
W
DATA2
A
A
DATA2
DATA2
DATA2
A
A
DATA3
DATA3
DATA3
DATA3
NA
A
P
P
243