MAX9850ETI+ Maxim Integrated Products, MAX9850ETI+ Datasheet - Page 25

• Manufacturer Part Number: MAX9850ETI+
• Description: IC AMP AUDIO .095W STER 28TQFN
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class ABr

Specifications of MAX9850ETI+

• Output Type: Headphones, 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 95mW x 2 @ 16 Ohm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Features: DAC, Depop, Digital Inputs, I²C, I²S, Line Level Inputs & Outputs, Mute, Shutdown, Volume Control
• Mounting Type: Surface Mount
• Package / Case: 28-WQFN Exposed Pad, 28-HWQFN
• Product: General Purpose Audio Amplifiers
• Output Power: 95 mW
• Operating Supply Voltage: 1.8 V to 3.6 V
• Supply Current: 7.6 mA
• Maximum Power Dissipation: 2857 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.8 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 14. General Purpose (0x3)
Read/Write, Bit Descriptions
00 = GPIO outputs low.
01 = GPIO is high impedance.
10 = GPIO outputs low and the ALERT output pulse
function is enabled.
11 = GPIO is high impedance and the ALERT output
pulse function is enabled.
GM(1:0) programs the GPIO output state and enables
or disables the ALERT output pulse function. The open-
drain GPIO output can be programmed to output static
high or a low. GPIO can also be programmed to pulse
to the opposite output level than the programmed out-
put state when an alert occurs. An alert occurs when
ALERT sets to 1 in the status A register. GM(1:0) has no
function when GPIO is configured as an input.
1 = Configure GPIO as an open-drain output.
0 = Configure GPIO as an input.
The state of GPD determines whether GPIO is an input
or an output.
00 = HPS debounce delay disabled.
01 = HPS debounce delay is a nominal 200ms.
10 = HPS debounce delay is a nominal 400ms.
11 = HPS debounce delay is a nominal 800ms.
DBDEL(1:0) controls the length of HPS debounce time.
The debounce time is derived from the charge-pump
clock.
1 = Enable mono mode.
0 = Disable mono mode, headphone outputs in stereo
mode.
Set MONO = 1 to force the headphone outputs to mono
mode. The stereo input signal is summed to one chan-
nel. The summed signal is output on the left headphone
output (HPL).
1 = Enables the zero-detect function.
0 = Disables the zero-detect function.
B7
GM(1:0)
B6
GPD
Debounce Delay Control (DBDEL(1:0))
B5
GPIO Output Mode Control (GM(1:0))
______________________________________________________________________________________
DBDEL(1:0)
General-Purpose Register
B4
Mono Mode Enable (MONO)
Zero-Detect Enable (ZDEN)
B3
Stereo Audio DAC with DirectDrive
GPIO Direction (GPD)
MONO
B2
B1
0
ZDEN
B0
Volume changes, headphone output muting, and enter-
ing/exiting shutdown occur only on the zero crossing of
the audio signal when ZDEN = 1. For optimum perfor-
mance, set SR(1:0) to 01.
Note: Any of the below interrupts can be configured to
trigger a hardware interrupt through GPIO. Program
GPD and GM(1:0) in the general-purpose register to
enable the ALERT output pulse function.
1 = A state change on SGPIO, when GPIO is an input,
will cause ALERT to set to 1.
0 = A state change on SGPIO, when GPIO is an input,
will not cause ALERT to set.
ISGPIO = 1 configures the MAX9850 to set ALERT = 1
when SGPIO changes state. The interrupt may only be
enabled when GPIO is an input.
1 = A state change on LCK will cause ALERT to set to 1.
0 = A state change on LCK will not cause ALERT to set.
ILCK = 1 configures the MAX9850 to set ALERT = 1
when the DAC’s internal PLL loses or achieves frequen-
cy lock with LRCLK. Program GM(1:0), while GPD = 1,
to configure GPIO as a hardware interrupt to alert a µC
when LCK changes state.
1 = A state change on SHPS will cause ALERT to set to 1.
0 = A state change on SHPS will not cause ALERT to set.
ISHPS = 1 configures the MAX9850 to set ALERT = 1
when SHPS changes state.
1 = A state change on VMN will cause ALERT to set to 1.
0 = A state change on VMN will not cause ALERT to set.
IVMN = 1 configures the MAX9850 to set ALERT = 1
when the headphone amplifier is programmed to and
reaches its minimum output volume. Program GM(1:0),
while GPD = 1, to configure GPIO as a hardware interrupt
to alert a µC when the headphone output volume is pro-
grammed to and reaches its minimum volume.
Table 15. Interrupt Enable (0x4)
Read/Write, Bit Descriptions
B7
0
Headphone Amplifier
ISGPIO ILCK
B6
Volume at Minimum Interrupt Enable (IVMN)
B5
PLL Lock Interrupt Enable (ILCK)
SGPIO Interrupt Enable (ISGPIO)
ISHPS IVMN
Interrupt Enable Register
SHPS Interrupt Enable (ISHPS)
B4
B3
B2
0
B1
0
IIOH
B0
25