3342-5 Peregrine Semiconductor, 3342-5 Datasheet
3342-5
Specifications of 3342-5
3342-50
Related parts for 3342-5
3342-5 Summary of contents
Page 1
... EVALUATION KIT USER’S MANUAL Peregrine Semiconductor Corportation PE3342 6175 Nancy Ridge Drive, San Diego, CA 92121 (858) 455-0660, Fax (858) 455-0770 1 http://www.peregrine-semi.com Doc. 79/0073~00C ...
Page 2
... Evaluation Kit Configuration for EEPROM Programming ……………………….. 13 Reprogramming the EEPROM………………………………………………………. 14 Peregrine Semiconductor Corportation ...
Page 3
... Peregrine Semiconductor Corp. Peregrine Semiconductor Corp., the Peregrine logotype, and UTSi are registered trademarks of Peregrine Semiconductor Corp. PE3342 is a trademark of Peregrine Semiconductor Corp. Peregrine Semiconductor Corp. reserves the right to make improvements to the hardware, firmware or software described in this manual at any time and without notice ...
Page 4
... Peregrine Semiconductor Corportation 4 Introduction Doc. 79/0073~00C ...
Page 5
... Introduction This Evaluation Kit is specifically designed for evaluating the PE3342 2.7 GHz Integer-N EEPROM PLL. The Evaluation Kit allows maximum flexibility for optimizing phase noise, spur, lock time and power performance for specific applications. Using the hardware and software provided in the Evaluation Kit, EEPROM mode programming can be demonstrated ...
Page 6
... Peregrine Semiconductor Corportation 6 Hardware Section Doc. 79/0073~00C ...
Page 7
... Mouse Parallel Port HTML Browser to access CD contents CAUTION: The PE3342-EK circuit contains components that might be damaged by exposure to voltages in excess of the specified voltage, including voltages produced by electrostatic discharges. Handle the board in accordance with procedures for handling static-sensitive components. Avoid applying excessive voltages to the power supply terminals or signal inputs or outputs ...
Page 8
... Evaluation Kit Configuration The PE3342 Evaluation Board is configured with an on-board VCO, TCXO reference and a second order active loop filter. The VCO tuning range is approximately 190 MHz with middle frequency at 2610+/- 25 for a tuning voltage 0.5 to 4.5 volts. The reference oscillator is 20 MHz. The loop filter is designed for a 1 MHz comparison frequency and a 2600 MHz output frequency with unity gain crossover at 66 kHz, phase margin of 65 degrees and 1 ...
Page 9
... Verify all supplies are turned off prior to connecting to evaluation board. Peregrine Semiconductor Corportation reference is used J6 center-to-right set to utilize on- board reference ...
Page 10
... Connect the +6/-2 V supply to J3-7 (+6V), J3-9 and -11 (GND), and J3-13 (-2V) Connect the +5 V supply to J3-17 (+) and J3-19 (GND) The PE3342 EEPROM on the evaluation board has been programmed and tested before stocking. No connection necessary for normal operation. To prevent the EEPROM from being accidentally erased or re-programmed, always place a jumper at center-to-right connection on the connector J8 to prevent VPP from being accidentally activated ...
Page 11
... Peregrine Semiconductor Corportation 11 Software Section Doc. 79/0073~00C ...
Page 12
... If the software doesn’t come with a CD nor floppy disks, follow the steps below the Peregrine PE3342 product page on our website at: http://www.peregrine- semi.com/prd_pll_PE3342.html. 5. Click on the “Software” button under the “Evaluation Kit Documentation” heading. ...
Page 13
... Verify all supplies are turned off prior to connecting to evaluation board. Connect the +3 V supply to J3-1 (+) and J3-3 (GND) Connect the +5 V supply to J3-17 (+) and J3-19 (GND) Connect the +6/-2 V supply to J3-7 (+6V), J3-9 and -11 (GND), and J3-13 (- 2V) Peregrine Semiconductor Corportation 13 Doc. 79/0073~00C ...
Page 14
... With the EE Programming kit set up completed as described in the previous section, the follow steps are for programming of the EEPROM register. Step 1: Start the “Peregrine EE PLL Control Software” program. Figure 4 shows one example of the screen. Peregrine Semiconductor Corportation reference is used J6 center-to-right set to utilize on-board J2 Jumpered ...
Page 15
... The prescaler enabled or disabled can be selected by the light blue Prescaler switch. “Enable” is the default selection. The enhancement mode enable function is currently unavailable. Data is sent to the evaluation board by clicking the dark blue “SEND DATA” button. Figure 4. Example of EEPROM Programming Software Screen. Peregrine Semiconductor Corportation 15 Doc. 79/0073~00C ...
Page 16
... Step 12: Move Switch 1 of SW1 to the “On” position. Step 13: Verify on the spectrum analyzer that the part locks to the desired frequency (J1 and J9 can be disconnected from the cables or remained connected for this operation). Step 14: To exit the program, click the “QUIT” button. Peregrine Semiconductor Corportation 16 Doc. 79/0073~00C ...
Page 17
... Figure 5. Example of EEPROM Programming Software Screen when programming failed. Peregrine Semiconductor Corportation 17 Doc. 79/0073~00C ...