AD1892JR Analog Devices Inc, AD1892JR Datasheet - Page 5

• Manufacturer Part Number: AD1892JR
• Description: IC SAMPLE CONV W/RX 20BIT 28SOIC
• Manufacturer: Analog Devices Inc
• Type: Sample Rate Converterr

Specifications of AD1892JR

• Rohs Status: RoHS non-compliant
• Applications: Players, Recorders
• Voltage - Supply, Digital: 4.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Voltage - Supply, Analog: -

REV. 0
Decoded Channel Status Outputs (Continued)
Pin Name SOIC
CC
CD
CE
CON/PRO
CSCLK
19
18
17
15
16
I/O
O
O
O
O
O
Description
In consumer mode, CC is the inverse Channel Status Bit 3, Byte 0 (C3, pre-emphasis). CC = 0
indicates that the audio material has been pre-emphasized; CC = 1 indicates that the audio material
has not been pre-emphasized.
In professional mode, CC is the most significant bit of the two bits that encodes the emphasis status
of the audio material.
Table I illustrates the professional mode emphasis encoding.
In consumer mode, CD indicates that the audio material is original over all category codes. The
state of this bit is affected by both the generation status “L” bit (Channel Status Bit 15, Byte 1) and
the category code (Channel Status Bits 8 through 14, Byte 1) since the definition of the L bit is re-
versed for three of the category codes (001XXXX, 0111XXX, and 100XXXX). CD = 0 indicates
that the audio material is original. CD = 1 indicates that the audio material is a copy (first genera-
tion or higher).
In professional mode, CD is the inverse of Channel Status Bit 9, Byte 1. CD provides some infor-
mation about channel mode. See below for additional details.
In consumer mode, CE indicates the so-called “ignorant” category codes of “general” (0000 000)
and “A/D converter without copyright information” (0110 000). CE = 1 indicates that the audio
material is not encoded using an ignorant category code. CE = 0 indicates that the audio material is
encoded using an ignorant category code. This status output can be used in conjunction with the
CD output (Pin 18) to implement SCMS copy protection. See below for additional details.
In professional mode, CE indicates a Cyclic Redundancy Code (CRC) check error. CE = 0 indi-
cates that the calculated CRC value does not match the received CRC value. CE = 1 indicates that
the calculated CRC value does match the received CRC value. CE may be used to enable the dis-
play of the CA through CD states. If CE = 0, then CA through CD may be considered to be in
error, and their display should not be updated.
The Table II summarizes the function of the CA through CE pins, depending on the operating mode
(professional or consumer).
CON/PRO is defined as the inverse Channel Status bit 0, byte 0 (C0, pro/consumer). CON/PRO =
0 indicates professional mode. CON/PRO = 1 indicates consumer mode. The state of this pin inter-
nally determines the consumer/pro mode of the CA, CB, CC, CD and CE pins.
Channel Status Clock. Active HI (rising edge active). Outputs a pulse every 192 frames at the
start of the Channel Status block. Use the falling edge of this clock to latch the CA through CE
and CON/PRO output Channel Status signals. See Figure 38 for timing.
CC
1
1
0
0
Pin
CA
CB
CC
CD
CE
AD1892
Output
0 = Audio, 1 = Nonaudio
0 = Copy Permitted, 1 = Copy Inhibited
0 = Pre-emphasis, 1 = No Pre-emphasis
0 = Original, 1 = Copy
0 = Ignorant Category, 1 = Not Ignorant 0 = C.S. CRC Error, 1 = No C.S. CRC Error
Consumer
CB
1
0
1
0
C2
0
1
1
1
Table II. Decoded Channel Status Output Functions
Channel Status Bit
BYTE 0
Table I. Professional Mode Emphasis Encoding
C3
0
0
1
1
–5–
C4
0
0
0
1
0 = Audio, 1 = Nonaudio
Pre-emphasis Encoding
Pre-emphasis Encoding
Inverse of Channel Status Bit 9
Status
Emphasis not indicated. Receiver defaults to
no emphasis with manual override enabled.
None. Receiver manual override disabled.
50/15 s. Receiver manual override disabled.
CCITT J. 17. Receiver manual override disabled.
Professional
AD1892