PEF24911HV22XP Lantiq, PEF24911HV22XP Datasheet - Page 76
![](/photos/31/31/313132/64pin_mqfp_sml.jpg)
PEF24911HV22XP
Manufacturer Part Number
PEF24911HV22XP
Description
Manufacturer
Lantiq
Datasheet
1.PEF24911HV22XP.pdf
(155 pages)
Specifications of PEF24911HV22XP
Control Interface
HDLC
Lead Free Status / Rohs Status
Supplier Unconfirmed
- Current page: 76 of 155
- Download datasheet (3Mb)
PEF 24911
Functional Description
Loss of Signal
The “Loss of Signal” state is entered upon the detection of a failure condition i.e. loss of
receive signal (LSUE). The ACT bit is set to “0” and the C/I-channel indication LSL is
issued. The U-transceiver waits for the C/I-channel command RES1 to enter the
“Receive Reset” state.
Loss of Synchronization
The “Loss of Synchronization” state is entered upon the detection of a failure condition
i.e. loss of framing by the LT-receiver (LOF). The ACT-bit is set to “0” and the C/I-channel
indication RSY is issued. The U-transceiver waits for the C/I-channel command RES1 to
enter the “Tear Down Error” state and subsequently the “Receive Reset” state.
Pending Deactivation
“Pending Deactivation” is a transient state entered after the receipt of a DR-code. The
DEA-bit is set to “0”. Timer T10 assures that the DEA-bit is set to “0” in at least three
consecutive superframes before the transmit level is turned off.
Pending Transparent
“Pending Transparent” is a transient state entered upon the detection of ACT = 1 and left
by T8. The ACT-bit is set to “1”. The purpose of this state is to issue the C/I-channel
indication AI (corresponding to “ready for sending”) 24 ms after the ACT-bit has been set
to “1” by the LT-transceiver. This assures that under normal operating conditions the AI-
indication is issued first on the TE-side and only afterwards on the LT-side. Thus the
layer-2 receiver in the TE is already operational when the first layer-2 message is issued
by the LT-side.
Reset
The “Reset” state is entered with the unconditional command RES, respectively Pin-
RES. It is left when pin RESQ is inactive and the C/I-channel code DR is received. SL0
and DEAC are output in “Reset” state. The U-transceiver does not react to the receipt of
a wake-up signal TN.
Reset for Loop
“Reset for Loop” resets the receiver in order to guarantee a correct adaption of the echo-
and equalizer coefficients.
Receive Reset
The “Receive Reset” state assures that for a period of T7 no signal, especially no wake-
up signal TL, is sent on the U-interface, i.e. no activation procedure is started from the
LT-side. A wake-up signal TN, however, from the NT-side is acknowledged.
Data Sheet
66
2001-07-16
Related parts for PEF24911HV22XP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PEB22811H-V13X](/images/manufacturer_photos/0/3/379/lantiq_tmb.jpg)
Part Number:
Description:
Manufacturer:
Lantiq
Datasheet:
![ADM6996L-AA-T-1](/images/manufacturer_photos/0/3/379/lantiq_tmb.jpg)
Part Number:
Description:
Manufacturer:
Lantiq
Datasheet:
![PEF22810T-V21TR](/images/manufacturer_photos/0/3/379/lantiq_tmb.jpg)
Part Number:
Description:
Manufacturer:
Lantiq
Datasheet: