PIC18F1320-I/SO Microchip Technology Inc., PIC18F1320-I/SO Datasheet - Page 113

• Manufacturer Part Number: PIC18F1320-I/SO
• Description: Microcontroller; 8 KB Flash; 256 RAM; 256 EEPROM; 16 I/O; 18-Pin-PDIP
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F1320-I/SO

• A/d Inputs: 7-Channel, 10-Bit
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 16
• Interface: USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin SOIC
• Programmable Memory: 8K Bytes
• Ram Size: 256 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

14.0
The Timer3 module timer/counter has the following
features:
• 16-bit timer/counter
• Readable and writable (both registers)
• Internal or external clock select
• Interrupt-on-overflow from FFFFh to 0000h
• Reset from CCP module trigger
REGISTER 14-1:
 2004 Microchip Technology Inc.
(two 8-bit registers; TMR3H and TMR3L)
TIMER3 MODULE
bit 7
bit 6
bit 5-4
bit 3
bit 2
bit 1
bit 0
T3CON: TIMER3 CONTROL REGISTER
RD16: 16-bit Read/Write Mode Enable bit
1 = Enables register read/write of Timer3 in one 16-bit operation
0 = Enables register read/write of Timer3 in two 8-bit operations
Unimplemented: Read as ‘0’
T3CKPS1:T3CKPS0: Timer3 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T3CCP1: Timer3 and Timer1 to CCP1 Enable bits
1 = Timer3 is the clock source for compare/capture CCP module
0 = Timer1 is the clock source for compare/capture CCP module
T3SYNC: Timer3 External Clock Input Synchronization Control bit
(Not usable if the system clock comes from Timer1/Timer3.)
When TMR3CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR3CS = 0:
This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0.
TMR3CS: Timer3 Clock Source Select bit
1 = External clock input from Timer1 oscillator or T13CKI
0 = Internal clock (F
TMR3ON: Timer3 On bit
1 = Enables Timer3
0 = Stops Timer3
bit 7
Legend:
R = Readable bit
-n = Value at POR
R/W-0
RD16
(on the rising edge after the first falling edge)
U-0
—
OSC
T3CKPS1
/4)
R/W-0
W = Writable bit
‘1’ = Bit is set
T3CKPS0
R/W-0
Figure 14-1 is a simplified block diagram of the Timer3
module.
Register 14-1 shows the Timer3 Control register. This
register controls the operating mode of the Timer3
module and sets the CCP clock source.
Register 12-1 shows the Timer1 Control register. This
register controls the operating mode of the Timer1
module, as well as contains the Timer1 Oscillator
Enable bit (T1OSCEN), which can be a clock source for
Timer3.
T3CCP1
PIC18F1220/1320
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
T3SYNC
R/W-0
TMR3CS
x = Bit is unknown
R/W-0
DS39605C-page 111
TMR3ON
R/W-0
bit 0