LAN9118-MT SMSC, LAN9118-MT Datasheet - Page 77

• Manufacturer Part Number: LAN9118-MT
• Description: IC ETHERNET CTRLR 10/100 100TQFP
• Manufacturer: SMSC
• Type: Single Chip MAC and PHYr

Specifications of LAN9118-MT

• Controller Type: Ethernet Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-TQFP, 100-VQFP
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 10 Mbps or 100 Mbps
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 100BASE-TX or 10BASE-T
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1013

High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
SMSC LAN9118
5.3.9
5.3.9.1
31-21
16-19
BITS
15-3
20
2
1
0
DESCRIPTION
Reserved
Must Be One (MBO). This bit must be set to “1” for normal device
operation.
TX FIFO Size (TX_FIF_SZ). Sets the size of the TX FIFOs in 1KB values
to a maximum of 14KB. The TX Status FIFO consumes 512 bytes of the
space allocated by TX_FIF_SIZ, and the TX data FIFO consumes the
remaining space specified by TX_FIF_SZ. The minimum size of the TX
FIFOs is 2KB (TX data and status combined). The TX data FIFO is used for
both TX data and TX commands.
The RX status and data FIFOs consume the remaining space, which is
equal to 16KB – TX_FIF_SIZ. See
Configurable FIFO Memory Allocation," on page 77
Reserved
32/16-bit Mode. When set, the LAN9118 is set for 32-bit operation. When
clear, it is configured for 16-bit operation. This field is the value of the
D32/nD16 strap.
Soft Reset Time-out (SRST_TO). If a software reset is attempted when the
internal PHY is not in the operational state (RX_CLK and TX_CLK running),
the reset will not complete and the soft reset operation will time-out and this
bit will be set to a ‘1’. The host processor must correct the problem and
issue another soft reset.
Soft Reset (SRST). Writing 1 generates a software initiated reset. This reset
generates a full reset of the MAC CSR’s. The SCSR’s (system command
and status registers) are reset except for any NASR bits. Soft reset also
clears any TX or RX errors (TXE/RXE). This bit is self-clearing.
Notes:
Do not attempt a soft reset unless the internal PHY is fully awake and
operational. After a PHY reset, or when returning from a reduced power
state, the PHY must be given adequate time to return to the operational
state before a soft reset can be issued. The internal RX_CLK and TX_CLK
signals must be running for a proper software reset. Please refer to
Section 6.8, "Reset Timing," on page 123
The LAN9118 must always be read at least once after power-up, reset, or
upon return from a power-saving state or write operations will not function.
HW_CFG—Hardware Configuration Register
This register controls the hardware configuration of the LAN9118 Ethernet Controller.
Note: The transmitter and receiver must be stopped before writing to this register. Refer to
Allowable settings for Configurable FIFO Memory Allocation
TX and RX FIFO space is configurable through the CSR - HW_CFG register defined above. The user
must select the FIFO allocation by setting the TX FIFO Size (TX_FIF_SZ) field in the hardware
Offset:
3.12.8, "Stopping and Starting the Transmitter," on page 52
Starting the Receiver," on page 56
74h
Section 5.3.9.1, "Allowable settings for
DATASHEET
for details on PHY reset timing.
77
for details on stopping the transmitter and receiver.
for more information.
Size:
and
32 bits
Section 3.13.4, "Stopping and
TYPE
R/W
R/W
RO
RO
RO
RO
SC
Revision 1.5 (07-11-08)
DEFAULT
5h
0
0
0
-
-
-
Section