CY7C63801-PXC Cypress Semiconductor Corp, CY7C63801-PXC Datasheet - Page 23

• Manufacturer Part Number: CY7C63801-PXC
• Description: IC USB PERIPHERAL CTRLR 16-DIP
• Manufacturer: Cypress Semiconductor Corp
• Series: CY7Cr

Specifications of CY7C63801-PXC

• Controller Type: USB Peripheral Controller
• Interface: USB
• Voltage - Supply: 4 V ~ 5.5 V
• Current - Supply: 40mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Package Type: MDIP
• Mounting: Through Hole
• Pin Count: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1001 - ISP 4PORT CYPRESS ENCORE II MCUCY4623 - KIT MOUSE REFERENCE DESIGN428-1774 - EXTENSION KIT FOR ENCORE II428-1773 - KIT DEVELOPMENT ENCORE II
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

Table 10-2. LPOSC Trim (LPOSCTR) [0x36] [R/W]
Table 10-3. CPU/USB Clock Config
Document 38-08035 Rev. *N
This register is used to calibrate the 32 kHz Low speed Oscillator. The reset value is undefined but during boot the SROM writes
a calibration value that is determined during manufacturing tests. This value does not require change during normal use. This
is the meaning of ‘D’ in the Default field. If the 32 kHz Low power bit is written, care must be taken to not disturb the
32 kHz Bias Trim and the 32 kHz Freq Trim fields from their factory calibrated values.
Bit 7: 32 kHz Low Power
0 = The 32 kHz Low speed Oscillator operates in normal mode
1 = The 32 kHz Low speed Oscillator operates in a low power mode. The oscillator continues to function normally, but with
reduced accuracy.
Bit 6: Reserved
Bit [5:4]: 32 kHz Bias Trim [1:0]
These bits control the bias current of the low power oscillator.
0 0 = Mid bias
0 1 = High bias
1 0 = Reserved
1 1 = Reserved
Note Do not program the 32 kHz Bias Trim [1:0] field with the reserved 10b value because the oscillator does not oscillate at all
corner conditions with this setting.
Bit [3:0]: 32 kHz Freq Trim [3:0]
These bits are used to trim the frequency of the low power oscillator.
Bit 7: Reserved
Bit 6: USB CLK/2 Disable
This bit only affects the USBCLK when the source is the external clock. When the USBCLK source is the Internal 24 MHz
Oscillator, the divide by two is always enabled
0 = USBCLK source is divided by two. This is the correct setting to use when the Internal 24 MHz Oscillator is used, or when
the external source is used with a 24 MHz clock
1 = USBCLK is undivided. Use this setting only with a 12 MHz external clock
Bit 5: USB CLK Select
This bit controls the clock source for the USB SIE.
0 = Internal 24 MHz Oscillator. With the presence of USB traffic, the Internal 24 MHz Oscillator is trimmed to meet the USB
requirement of 1.5% tolerance (see
1 = External clock—Internal Oscillator is not trimmed to USB traffic. Proper USB SIE operation requires a 12 MHz or 24 MHz
clock accurate to <1.5%.
Bit [4:1]: Reserved
Bit 0: CPU CLK Select
0 = Internal 24 MHz Oscillator.
1 = External clock—External clock at CLKIN (P0.0) pin.
Note The CPU speed selection is configured using the OSC_CR0 Register
Read/Write
Read/Write
Default
Default
Field
Field
Bit #
Bit #
32 kHz Low
Reserved
Power
R/W
7
0
7
–
0
USB CLK/2
Reserved
Disable
R/W
D
6
–
6
0
Table 10-5 on page
(
CPUCLKCR) [0x30] [R/W]
USB CLK Select
R/W
R/W
32 kHz Bias Trim [1:0]
D
5
5
0
25)
R/W
D
4
4
–
0
R/W
(Table 10-4 on page
D
3
3
–
0
Reserved
32 kHz Freq Trim [3:0]
R/W
CY7C63310, CY7C638xx
D
2
2
–
0
24).
R/W
D
1
1
–
0
CPUCLK Select
Page 23 of 86
R/W
R/W
D
0
0
0
[+] Feedback