PCA9564D,112 NXP Semiconductors, PCA9564D,112 Datasheet - Page 15

• Manufacturer Part Number: PCA9564D,112
• Description: IC CTRL PARALLEL/I2C BUS 20-SOIC
• Manufacturer: NXP Semiconductors

Specifications of PCA9564D,112

• Controller Type: Parallel Bus to I²C Bus Controller
• Interface: I²C
• Voltage - Supply: 2.3 V ~ 3.6 V
• Current - Supply: 6mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• For Use With: 568-4001 - DEMO BOARD FOR PCA9564
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-1062-5; 935272894112; PCA9564D

Philips Semiconductors
Slave Transmitter Mode: In the slave transmitter mode, a number
of data bytes are transmitted to a master receiver (see Figure 5).
Data transfer is initialized as in the slave receiver mode. When
I2CADR and I2CCON have been initialized, SIO waits until it is
addressed by its own slave address followed by the data direction
bit which must be “1” (R) for SIO to operate in the slave transmitter
mode. After its own slave address and the R bit have been received,
the serial interrupt flag (SI) is set and a valid status code can be
read from I2CSTA. This status code is used to vector to an interrupt
service routine, and the appropriate action to be taken for each of
these status codes is detailed in Table 5. The slave transmitter mode
may also be entered if arbitration is lost while SIO is in the master
mode (see state B0H).
If the AA bit is reset during a transfer, SIO will transmit the last byte
of the transfer and enter state C8H. SIO is switched to the not
addressed slave mode and will ignore the master receiver if it
continues the transfer. Thus the master receiver receives all 1s as
serial data. While AA is reset, SIO does not respond to its own slave
address. However, the I
recognition may be resumed at any time by setting AA. This means
that the AA bit may be used to temporarily isolate SIO from the
I
Miscellaneous States: There are four I2CSTA codes that do not
correspond to a defined SIO hardware state (see Table 6). These
are discussed below.
I2CSTA = F8H:
This status code indicates that no relevant information is available
because the serial interrupt flag, SI, is not yet set. This occurs on a
STOP condition and when SIO is not involved in a serial transfer.
I2CSTA = 00H:
This status code indicates that a bus error has occurred during an
SIO serial transfer. A bus error is caused when a START or STOP
condition occurs at an illegal position in the format frame. Examples
of such illegal positions are during the serial transfer of an address
byte, a data byte, or an acknowledge bit. A bus error may also be
caused when external interference disturbs the internal SIO signals.
When a bus error occurs, SI is set. To recover from a bus error, the
microcontroller must send an external reset signal to reset the SIO.
I2CSTA = 70H:
This status code indicates that the SDA line is stuck LOW when the
SIO, in master mode, is trying to send a START condition.
2006 Sep 01
2
C-bus.
Parallel bus to I
08H
S
SLA
2
C-bus is still monitored, and address
2
C-bus controller
W
Figure 6. Simultaneous repeated START conditions from 2 masters
18H
A
DATA
OTHER MASTER SENDS REPEATED
START CONDITION EARLIER
28H
A
15
S
I2CSTA = 90H:
This status code indicates that the SCL line is stuck LOW.
Some Special Cases: The SIO hardware has facilities to handle the
following special cases that may occur during a serial transfer:
A repeated START condition may be generated in the master
transmitter or master receiver modes. A special case occurs if
another master simultaneously generates a repeated START
condition (see Figure 6). Until this occurs, arbitration is not lost by
either master since they were both transmitting the same data.
If the SIO hardware detects a repeated START condition on the
I
use the repeated START as its own and continue with the sending of
the slave address.
Arbitration may be lost in the master transmitter and master receiver
modes. Loss of arbitration is indicated by the following states in
I2CSTA; 38H, 68H, and B0H (see Figures 2 and 3).
NOTE: In order to exit state 38H, a Timeout, Reset, or external
Stop are required.
If the STA flag in I2CCON is set by the routines which service these
states, then, if the bus is free again, a START condition (state 08H)
is transmitted without intervention by the CPU, and a retry of the
total serial transfer can commence.
In some applications, it may be possible for an uncontrolled source
to cause a bus hang-up. In such situations, the problem may be
caused by interference, temporary interruption of the bus or a
temporary short-circuit between SDA and SCL.
If an uncontrolled source generates a superfluous START or masks
a STOP condition, then the I
STA flag is set and bus access is not obtained within a reasonable
amount of time, then a forced access to the I
the I
then the ’64 concludes that no other master is using the bus and
sends a START condition.
2
C-bus before generating a repeated START condition itself, it will
S
D
F
ORCED
IMULTANEOUS
ATA
2
C-bus stays idle for a time period equal to the time out period,
BOTH MASTERS CONTINUE
WITH SLA TRANSMISSION
T
RANSFER
A
CCESS TO THE
R
A
EPEATED
FTER
L
I
OSS OF
2
START C
C B
2
C-bus stays busy indefinitely. If the
US
A
RBITRATION
ONDITIONS FROM
2
C-bus is possible. If
SU00975
PCA9564
Product data sheet
T
WO
M
ASTERS