UDA1384H/N1,557 NXP Semiconductors, UDA1384H/N1,557 Datasheet - Page 50

• Manufacturer Part Number: UDA1384H/N1,557
• Description: IC AUDIO CODEC 44-QFP
• Manufacturer: NXP Semiconductors
• Type: Audio Codecr

Specifications of UDA1384H/N1,557

• Data Interface: I²C, Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 5 / 6
• Sigma Delta: No
• S/n Ratio, Adcs / Dacs (db) Typ: 98 / 110 (Differential), 98 / 110 (Single-Ended)
• Voltage - Supply, Analog: 2.7 V ~ 3.6 V
• Voltage - Supply, Digital: 2.7 V ~ 3.6 V
• Operating Temperature: -20°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 44-MQFP, 44-PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-3450; 935274756557; UDA1384H

Philips Semiconductors
18. Handling information
19. Soldering
9397 750 14366
Product data sheet
19.1 Introduction to soldering surface mount packages
19.2 Reflow soldering
19.3 Wave soldering
Inputs and outputs are protected against electrostatic discharge in normal handling.
However, to be completely safe, it is desirable to take normal precautions appropriate to
handling integrated circuits.
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 C to 270 C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
•
•
below 225 C (SnPb process) or below 245 C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
thick/large packages.
Rev. 02 — 17 January 2005
2.5 mm
3
so called small/thin packages.
Multichannel audio coder-decoder
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
350 mm
UDA1384
3
so called
50 of 55