IDT92HD75B2X5NLGXYAX8 IDT, Integrated Device Technology Inc, IDT92HD75B2X5NLGXYAX8 Datasheet - Page 25

• Manufacturer Part Number: IDT92HD75B2X5NLGXYAX8
• Description: IC AUDIO CODEC HD 4CH 32-VFQFPN
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Audio Codec, HDr

Specifications of IDT92HD75B2X5NLGXYAX8

• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: No
• S/n Ratio, Adcs / Dacs (db) Typ: 86 / 95
• Dynamic Range, Adcs / Dacs (db) Typ: 86 / 93
• Voltage - Supply, Analog: 3.14 V ~ 3.47 V; 3.8 V ~ 4.2 V; 4.28 V ~ 4.73 V; 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 32-VFQFN, 32-VFQFPN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 92HD75B2X5NLGXYAX8

4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
92HD75B
4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
•
1.4.16.3. Hardware Implementation
The Volume Knob interface is comprised of two input pins, CODEC pins 2 and 4. Both pins have
internal pull-up resistors, so only two push button switches are required for most implementations.
Typically, a series resistor and shunt capacitor are used to help reduce noise and prevent damage
from ESD and other potential faults. An example circuit is shown below.
•
•
•
•
INDIRECT MODE
actual gain will be -95.25dB. For example, if the Volume Knob is set to 0x3F (-48dB) and the
DAC amplifier volume is set to 0x1F (-72dB) then the DAC volume will be set to -95.25dB.
Direct mode is enabled by setting bit 7 in the Volume Knob Cntrl verb (F0F). The volume is
reflected in the Volume Knob Cntrl bits 6:0 and the step size is 0.75dB. In direct mode, soft-
ware can read or write the volume in the Volume Knob widget.
In indirect mode, the Volume Knob widget does not directly control the DAC amplifier gains.
An event on the volume Up/Down pins will increment/decrement the value in the Volume
Knob Cntrl verb (F0F) volume bits (bits 6:0) just as in Direct mode. However, instead of
adjusting the DAC amplifier gain, an unsolicited response is generated (if enabled) and the
control software must read the volume in the Volume Knob widget and take appropriate
action. Indirect mode is particularly useful when it is undesirable to control all of the DAC
amplifier volumes at the same time, or when implementing ADC volume control.
In indirect mode, there are only 128 volume levels in the Volume Knob Cntrl volume bits, the
value will not go beyond the lower and upper limits (0x0 or 0x7F), and an unsolicited
response will not be generated if an input event tries to go beyond these limits. Therefore, it
is the responsibility of the controlling software to monitor the volume in the Volume Knob
Widget and take appropriate action.
Indirect mode is enabled by clearing bit 7 in the Volume Knob Cntrl verb (F0F). The volume
is reflected in the Volume Knob Cntrl bits 6:0 and the step size is 0.75dB. In direct mode,
software can read or write the volume in the Volume Knob widget.
Figure 9. Volume Knob
25
92HD75B
PC AUDIO
V 1.0 01-09