MAX9867EWV+T Maxim Integrated Products, MAX9867EWV+T Datasheet - Page 41

• Manufacturer Part Number: MAX9867EWV+T
• Description: IC STEREO AUD CODEC LP 30WLP
• Manufacturer: Maxim Integrated Products
• Type: Stereo Audior

Specifications of MAX9867EWV+T

• Data Interface: I²C, Serial
• Resolution (bits): 18 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 85 / 90
• Voltage - Supply, Analog: 1.65 V ~ 1.95 V
• Voltage - Supply, Digital: 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 30-WLP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX9867EWV+T; MAX9867EWV+TTR

MCLK = 13MHz, slave mode, BCLK and LRCLK not
externally supplied:
1) Configure the digital audio interface for f
2) Disable JACKSNS (JDETEN = 0).
3) Enable the left and right ADC; take the MAX9867 out
4) Calibrate the offset:
5) Calibrate the gain:
Table 14. ADC Input Register
ADC Input
a. Enable the AUX input (AUXEN = 1).
b. Enable the offset calibration (AUXCAL = 1).
c. Wait 40ms.
d. Complete calibration (AUXCAL = 0).
a. Start gain calibration (AUXGAIN = 1).
(PSCLK = 01, FREQ = 0x0, PLL = 0, NI = 0x5ABE,
MAS = 0).
of shutdown (ADLEN = ADREN = SHDN = 1).
MXINL/MXINR
REGISTER
AUXGAIN
AUXCAP
AUXCAL
AUXEN
BITS
Complete DC Measurement Example
______________________________________________________________________________________
Left/Right ADC Audio Input Mixer
00 = No input is selected.
01 = Left/right analog microphone
10 = Left/right line input
11 = Left/right analog microphone + line input
Note: If the right-line input is disabled, then the left-line input is connected to both mixers. Enabling the
left and right digital microphones disables the left and right audio mixers, respectively. See DIGMICL/
DIGMICR in Table 15 for more details.
Auxiliary Input Capture
0 = Update AUX with the voltage at JACKSNS/AUX.
1 = Hold AUX for reading.
Auxiliary Input Gain Calibration
0 = Normal operation
1 = The input buffer is disconnected from JACKSNS/AUX and connected to an internal voltage reference.
Auxiliary Input Offset Calibration
0 = Normal operation
1 = JACKSNS/AUX is disconnected from the input and the ADC automatically calibrates out any internal
Auxiliary Input Enable
0 = Use JACKSNS/AUX for jack detection.
1 = Use JACKSNS/AUX for DC measurements.
Note: For AUXEN = 1, set MXINR = 00, ADLEN = 1, and ADREN = 1.
B7
offsets.
Ultra-Low Power Stereo Audio Codec
While in this mode, read the AUX register and store the value. Use the stored value as a gain
calibration factor, K, on subsequent readings.
MXINL
B6
S
= 48kHz
B5
MXINR
B4
6) Measure the voltage on JACKSNS/AUX:
7) DC measurement complete.
b. Wait 40ms.
c. Freeze the measurement results (AUXCAP = 1).
d. Read AUX and store the value in memory to cor-
e. Complete calibration (AUXGAIN = AUXCAP =
a. Enable the AUX input (AUXEN = 1).
b. Wait 40ms.
c. Freeze the measurement results (AUXCAP = 1).
d. Read AUX and correct with the gain calibration
e. Complete measurement (AUXCAP = 0).
AUXCAP
FUNCTION
rect all future measurements (k = AUX[15:0]).
AUXEN = 0).
value.
B3
AU X GAIN
B2
AUXCAL
B1
AUXEN
B0
REGISTER
ADDRESS
0x14
41