CS42526-CQZ Cirrus Logic Inc, CS42526-CQZ Datasheet - Page 23

• Manufacturer Part Number: CS42526-CQZ
• Description: IC CODEC S/PDIF RCVR 64LQFP
• Manufacturer: Cirrus Logic Inc
• Type: General Purposer

Specifications of CS42526-CQZ

• Package / Case: 64-LQFP
• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 6
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 114 / 114
• Voltage - Supply, Analog: 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.13 V ~ 5.25 V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 6
• Conversion Rate: 192 KSPS
• Interface Type: Serial (SPI)
• Resolution: 24 bit
• Operating Supply Voltage: 3.3 V, 5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 2 ADC/6 DAC
• Thd Plus Noise: - 100 dB ADC / - 100 dB DAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 598-1037

DS585F1
4.3.3
4.3.4
CX_SDINx
Digital Volume and Mute Control
Each DAC’s output level is controlled via the Volume Control registers operating over the range of 0 to
-127 dB attenuation with 0.5 dB resolution. See
14h)” on page
rate controlled by the SZC[1:0] bits in the Digital Volume Control register. See
(address 0Dh)” on page
Each output can be independently muted via mute control bits in the register
0Eh)” on page
value (-127 dB). When the XX_MUTE bit is disabled, the corresponding DAC returns to the attenuation
level set in the Volume Control register. The attenuation is ramped up and down at the rate specified by
the SZC[1:0] bits.
The Mute Control pin, MUTEC, is typically connected to an external mute control circuit. The Mute Control
pin outputs high impedance during Power-Up or in Power-Down Mode by setting the PDN bit in the reg-
ister
controlled by the user via the control port, or automatically asserted high when zero data is present on all
DAC inputs, or when serial port clock errors are present. To prevent large transients on the output, it is
desirable to mute the DAC outputs before the Mute Control pin is asserted. Please see the MUTEC pin
in the Pin Descriptions section for more information.
Each of the RXP1/GPO1-RXP7/GPO7 can be programmed to provide a hardware MUTE signal to indi-
vidual circuits. When not used as an S/PDIF input, each pin can be programmed as an output, with spe-
cific muting capabilities as defined by the function bits in the register
(addresses 29h to 2Fh)” on page
ATAPI Specification
The CS42526 implements the channel-mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to
mation.
“Power Control (address 02h)” on page 47
Right Channel
Left Channel
Audio Data
Audio Data
59. When enabled, each XX_MUTE bit attenuates the corresponding DAC to its maximum
59. Volume control changes are programmable to ramp in increments of 0.125 dB at the
Figure 8. ATAPI Block Diagram (x = channel pair 1, 2, or 3)
57.
70.
Σ
to a ‘1’. Once out of Power-Down Mode, the pin can be
“Volume Control (addresses 0Fh, 10h, 11h, 12h, 13h,
Table 16 on page 61
A Channel
B Channel
Volume
Volume
Control
Control
“RXP/General-Purpose Pin Control
and
Σ
Figure 8
“Volume Transition Control
“Channel Mute (address
MUTE
MUTE
for additional infor-
CS42526
AOUTAx
AOUTBx
23