EPM9560ARC208-10 Altera, EPM9560ARC208-10 Datasheet - Page 18

• Manufacturer Part Number: EPM9560ARC208-10
• Description: IC MAX 9000 CPLD 560 208-RQFP
• Manufacturer: Altera
• Series: MAX® 9000r

Specifications of EPM9560ARC208-10

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 10.0ns
• Voltage Supply - Internal: 4.75 V ~ 5.25 V
• Number Of Logic Elements/blocks: 35
• Number Of Macrocells: 560
• Number Of Gates: 12000
• Number Of I /o: 153
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 208-RQFP
• Voltage: 3.3V/5V
• Memory Type: EEPROM
• Number Of Logic Elements/cells: 35
• Family Name: MAX 9000
• # Macrocells: 560
• Number Of Usable Gates: 12000
• Frequency (max): 144.9MHz
• Propagation Delay Time: 10ns
• Number Of Logic Blocks/elements: 35
• # I/os (max): 153
• Operating Supply Voltage (typ): 5V
• In System Programmable: Yes
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: RQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-2363

MAX 9000 Programmable Logic Device Family Data Sheet
Output
Configuration
18
The output buffer in each IOC has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces board-level noise and adds a nominal timing delay to the
output buffer delay (t
speed-critical outputs in systems that are adequately protected against
noise. Designers can specify the slew rate on a pin-by-pin basis during
design entry or assign a default slew rate to all pins on a global basis. The
slew rate control affects both rising and falling edges of the output signals.
The MAX 9000 device architecture supports the MultiVolt I/O interface
feature, which allows MAX 9000 devices to interface with systems of
differing supply voltages. The 5.0-V devices in all packages can be set for
3.3-V or 5.0-V I/O pin operation. These devices have one set of V
for internal operation and input buffers (VCCINT), and another set for I/O
output drivers (VCCIO).
The VCCINT pins must always be connected to a 5.0-V power supply.
With a 5.0-V V
therefore compatible with 3.3-V and 5.0-V inputs.
Table 6. Peripheral Bus Sources
Peripheral Control
OE0/ENA0
OE1/ENA1
OE2/ENA2
OE3/ENA3
OE4/ENA4
OE5
OE6
OE7/CLR1
CLR0/ENA5
CLK0
CLK1
CLK2
CLK3
Signal
CCINT
Row C
Row B
Row A
Row B
Row A
Row D
Row C
Row B/GOE
Row A/GCLR Row A/GCLR Row A/GCLR Row A/GCLR
GCLK1
GCLK2
Row D
Row C
level, input voltages are at TTL levels and are
OD
EPM9320
EPM9320A
) parameter. The fast slew rate should be used for
Row E
Row E
Row E
Row B
Row A
Row D
Row C
Row B/GOE
GCLK1
GCLK2
Row D
Row C
EPM9400
Source
Row F
Row F
Row E
Row B
Row A
Row D
Row C
Row B/GOE
GCLK1
GCLK2
Row D
Row C
EPM9480
Altera Corporation
Row G
Row F
Row E
Row B
Row A
Row D
Row C
Row B/GOE
GCLK1
GCLK2
Row D
Row C
EPM9560
EPM9560A
CC
pins