AD9788BSVZ Analog Devices Inc, AD9788BSVZ Datasheet - Page 35

• Manufacturer Part Number: AD9788BSVZ
• Description: IC DAC 16BIT 800MSPS 100TQFP
• Manufacturer: Analog Devices Inc
• Series: TxDAC®r

Specifications of AD9788BSVZ

• Data Interface: Serial
• Design Resources: Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141)
• Number Of Bits: 16
• Number Of Converters: 2
• Voltage Supply Source: Analog and Digital
• Power Dissipation (max): 450mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-TQFP Exposed Pad, 100-eTQFP, 100-HTQFP, 100-VQFP
• Resolution (bits): 16bit
• Sampling Rate: 800MSPS
• Input Channel Type: Parallel
• Digital Ic Case Style: QFP
• No. Of Pins: 100
• Operating Temperature Range: -40°C To +85°C
• Number Of Channels: 2
• Resolution: 16b
• Interface Type: Parallel
• Single Supply Voltage (typ): 3.3V
• Dual Supply Voltage (typ): Not RequiredV
• Settling Time: 0.02us
• Architecture: Interpolation Filter
• Power Supply Requirement: Analog and Digital
• Output Type: Current
• Integral Nonlinearity Error: ±3.7LSB
• Single Supply Voltage (min): 3.13V
• Single Supply Voltage (max): 3.47V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: TQFP EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9788-EBZ - BOARD EVAL FOR AD9788
• Settling Time: -
• Lead Free Status / Rohs Status: Compliant

Setting the Frequency of DATACLK
The DATACLK signal is derived from the internal DAC sample
clock, DACCLK. The frequency of DATACLK output depends
on several programmable settings. The relationship between the
frequency of DACCLK and DATACLK is
where the variables have the values shown in Table 26.
Table 26. DACCLK to DATACLK Divisor Values
Variable
IF
P
f
DATACLK
Value
Interpolation factor
0.5 (if single port is enabled)
1 (if dual port is selected)

f
IF
DACCLK

P
DACCLK
DACCLK
REFCLK
REFCLK
SYNC_I
SYNC_I
INPUT
INPUT
DATA
DATA
Register
0x01
0x01
Address
t
S_SYNC
t
H_SYNC
Bits
[7:6]
[4]
Figure 49. REFCLK 2×
Figure 50. REFCLK 4×
Rev. A | Page 35 of 64
t
S_SYNC
t
SREFCLK
t
t
H_SYNC
SREFCLK
INPUT DATA REFERENCED TO REFCLK
In some systems, it may be more convenient to use the REFCLK
input instead of the DATACLK output as the input data timing
reference. If the frequency of DACCLK is equal to the frequency
of the data input (PLL is bypassed and no interpolation is used),
the timing parameter “Data with respect to REFCLK” shown in
Table 25 applies directly without further considerations. If the
frequency of DACCLK is greater than the frequency of the data
input, a divider is used to generate the internal data sampling clock
(DCLK_SMP). This divider creates a phase ambiguity between
REFCLK and DCLK_SMP, which, in turn, causes a sampling
time uncertainty. To establish fixed setup and hold times for the
data interface, this phase ambiguity must be eliminated.
To eliminate the phase ambiguity, the SYNC_I input pins
(Pin 13 and Pin 14) must be used to synchronize the data to
a specific DCLK_SMP phase. The specific steps for accom-
plishing this are detailed in the Device Synchronization section.
The timing relationships between SYNC_I, DACCLK, REFCLK,
and the input data are shown in Figure 49 through Figure 51.
t
HREFCLK
t
HREFCLK
AD9785/AD9787/AD9788