AD1674KNZ Analog Devices Inc, AD1674KNZ Datasheet - Page 4

• Manufacturer Part Number: AD1674KNZ
• Description: IC ADC 12BIT 100KSPS 28-DIP
• Manufacturer: Analog Devices Inc

Specifications of AD1674KNZ

• Data Interface: Parallel
• Number Of Bits: 12
• Sampling Rate (per Second): 100k
• Number Of Converters: 1
• Power Dissipation (max): 825mW
• Voltage Supply Source: Dual ±
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 28-DIP (0.600", 15.24mm)
• Resolution (bits): 12bit
• Sampling Rate: 100kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Digital: 4.5V To 5.5V
• Supply Current: 14mA
• Digital Ic Case Style: DIP
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 100KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 10/20/±5/±10V
• Differential Input: No
• Power Supply Requirement: Dual
• Single Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (typ): ±12/±15V
• Dual Supply Voltage (min): ±11.4V
• Dual Supply Voltage (max): ±16.5V
• Power Dissipation: 575mW
• Integral Nonlinearity Error: ±0.5LSB
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP W
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

DSCC FORM 2234
APR 97
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the
full ambient operating temperature range.
tests for each subgroup are defined in table I.
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535
and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
HANDBOOKS
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Functional block diagram. The functional block diagram shall be as specified on figure 3.
3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43216-5000
STANDARD
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
SIZE
A
REVISION LEVEL
A
SHEET
5962-93164
4