ICS8536CGI-33LF IDT, Integrated Device Technology Inc, ICS8536CGI-33LF Datasheet - Page 10

• Manufacturer Part Number: ICS8536CGI-33LF
• Description: IC CLK FAN BUFF MUX 1:6 20TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution), Multiplexerr
• Series: HiPerClockS™r

Specifications of ICS8536CGI-33LF

• Number Of Circuits: 1
• Ratio - Input:output: 2:6
• Differential - Input:output: No/Yes
• Input: LVCMOS, LVTTL, Crystal
• Output: LVCMOS, LVPECL
• Frequency - Max: 266MHz
• Voltage - Supply: 2.375 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Frequency-max: 266MHz
• Number Of Clock Inputs: 2
• Mode Of Operation: Single-Ended
• Output Frequency: 266MHz
• Output Logic Level: LVCMOS/LVPECL/LVTTL
• Operating Supply Voltage (min): 2.375V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.465V
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Signal Type: LVCMOS/LVTTL
• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 800-1962-5; 8536CGI-33LF; ICS8536CGI-33LF

R
I
C
For applications not requiring the use of the crystal oscillator input,
both XTAL_IN and XTAL_OUT can be left floating. Though not
required, but for additional protection, a 1k
from XTAL_IN to ground.
CLK I
For applications not requiring the use of a clock input, it can be
left floating. Though not required, but for additional protection, a
1k
LVCMOS C
All control pins have internal pull-ups or pull-downs; additional
resistance is not required but can be added for additional
protection. A 1k
C
The ICS8536I-33 has been characterized with 18pF parallel
resonant crystals. The capacitor values, C1 and C2, shown in
Figure 2 below were determined using an 18pF parallel resonant
crystal and were chosen to minimize the ppm error. These
IDT
NPUTS
RYSTAL
ECOMMENDATIONS FOR
RYSTAL
ICS8536I-33
LOW SKEW, 1-TO-6, CRYSTAL OSCILLATOR/LVCMOS-TO-3.3V, 2.5V LVPECL/LVCMOS FANOUT BUFFER
™
resistor can be tied from the CLK input to ground.
/ ICS
NPUT
:
I
NPUTS
™
I
3.3V, 2.5V LVPECL/ LVCMOS FANOUT BUFFER
NPUT
ONTROL
I
resistor can be used.
NTERFACE
P
INS
U
NUSED
18pF Parallel Crystal
I
NPUT AND
A
resistor can be tied
X1
PPLICATION
F
IGURE
O
UTPUT
2. C
P
RYSTAL
INS
C1
27p
C2
27p
10
I
NFORMATION
I
O
LVCMOS O
All unused LVCMOS output can be left floating. There should be
no trace attached.
LVPECL O
All unused LVPECL outputs can be left floating. We recommend
that there is no trace attached. Both sides of the differential output
pair should either be left floating or terminated.
same capacitor values will tune any 18pF parallel resonant
crystal over the frequency range and other parameters speci-
fied in this data sheet. The optimum C1 and C2 values can be
slightly adjusted for different board layouts.
NPU
XTAL_OUT
XTAL_IN
UTPUTS
t I
NTERFACE
:
UTPUTS
UTPUTS
ICS8536CGI-33 REV. B OCTOBER 27, 2008