M25P32-VMW3TGB NUMONYX, M25P32-VMW3TGB Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M25P32-VMW3TGB
Manufacturer Part Number
M25P32-VMW3TGB
Description
Manufacturer
NUMONYX
Datasheet
1.M25P32-VMW3TGB.pdf
(54 pages)
Specifications of M25P32-VMW3TGB
Cell Type
NOR
Density
32Mb
Access Time (max)
8ns
Interface Type
Serial (SPI)
Address Bus
1b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 125C
Package Type
SO W
Sync/async
Synchronous
Operating Temperature Classification
Automotive
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8b
Number Of Words
4M
Supply Current
8mA
Mounting
Surface Mount
Pin Count
8
Lead Free Status / RoHS Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P32-VMW3TGB
Manufacturer:
MICREL
Quantity:
1 200
Part Number:
M25P32-VMW3TGB
Manufacturer:
MICRON/美光
Quantity:
20 000
4
4.1
4.2
4.3
4.4
Operating features
Page Programming
To program one data byte, two instructions are required: Write Enable (WREN), which is
one byte, and a Page Program (PP) sequence, which consists of four bytes plus data. This
is followed by the internal Program cycle (of duration t
To spread this overhead, the Page Program (PP) instruction allows up to 256 bytes to be
programmed at a time (changing bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few bytes (see
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be
applied, the bytes of memory need to have been erased to all 1s (FFh). This can be
achieved either a sector at a time, using the Sector Erase (SE) instruction, or throughout the
entire memory, using the Bulk Erase (BE) instruction. This starts an internal Erase cycle (of
duration t
The Erase instruction must be preceded by a Write Enable (WREN) instruction.
Polling during a Write, Program or Erase cycle
A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase
(SE or BE) can be achieved by not waiting for the worst case delay (t
Write In Progress (WIP) bit is provided in the Status Register so that the application program
can monitor its value, polling it to establish when the previous Write cycle, Program cycle or
Erase cycle is complete.
Fast Program/Erase mode
The Fast Program/Erase mode is used to speed up programming/erasing. The device
enters the Fast Program/Erase mode during the Page Program, Sector Erase or Bulk Erase
instruction whenever a voltage equal to V
The use of the Fast Program/Erase mode requires specific operating conditions in addition
to the normal ones (V
the voltage applied to the W/V
ambient temperature, T
the cumulated time during which W/V
SE
or t
BE
).
CC
must be within the normal operating range):
A
must be 25 °C ±10 °C,
PP
pin must be equal to V
PPH
PP
is at V
is applied to the W/V
PPH
PP
should be less than 80 hours
).
PPH
(see
PP
W
Page Program
pin.
, t
Table
PP
, t
SE
10)
, or t
BE
(PP)).
). The
13/54