AD9854ASQ Analog Devices Inc, AD9854ASQ Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9854ASQ
Manufacturer Part Number
AD9854ASQ
Description
Manufacturer
Analog Devices Inc
Datasheet
1.AD9854ASQ.pdf
(52 pages)
Specifications of AD9854ASQ
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9854ASQ
Manufacturer:
ADI
Quantity:
271
Part Number:
AD9854ASQ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9854ASQZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9854
INSTRUCTION BYTE
The instruction byte contains the following information.
Table 10. Instruction Byte Information
MSB
R/W
R/ W —Bit 7 determines whether a read or write data transfer
occurs following the instruction byte. Logic high indicates read
operation. Logic 0 indicates a write operation.
Bit 6, Bit 5, and Bit 4 are dummy bits (don’t care).
A3, A2, A1, A0—Bit 3, Bit 2, Bit 1, and Bit 0 determine which
register is accessed during the data transfer portion of the
communication cycle. See Table 7 for register address details.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
SCLK
Serial Clock (Pin 21). The serial clock pin is used to
synchronize data to and from the AD9854 and to run the
internal state machines. SCLK maximum frequency is 10 MHz.
CS
Chip Select (Pin 22). Active low input that allows more than
one device on the same serial communication line. The SDO
and SDIO pins go to a high impedance state when this input is
high. If driven high during a communication cycle, that cycle is
suspended until CS is reactivated low. The chip select pin can be
tied low in systems that maintain control of SCLK.
SDIO
Serial Data I/O (Pin 19). Data is always written to the AD9854
on this pin. However, this pin can be used as a bidirectional
data line. The configuration of this pin is controlled by Bit 0 of
Register Address 20 hex. The default is Logic 0, which
configures the SDIO pin as bidirectional.
SDO
Serial Data Out (Pin 18). Data is read from this pin for protocols
that use separate lines for transmitting and receiving data. In
the case where the AD9854 operates in a single bidirectional
I/O mode, this pin does not output data and is set to a high
impedance state.
IO RESET
Synchronize I/O Port (Pin 17). Synchronizes the I/O port state
machines without affecting the contents of the addressable
registers. An active high input on the IO RESET pin causes the
current communication cycle to terminate. After the IO RESET
pin returns low (Logic 0), another communication cycle can begin,
starting with the instruction byte.
D6
X
D5
X
D4
X
D3
A3
D2
A2
D1
A1
LSB
A0
Rev. D | Page 36 of 52
NOTES ON SERIAL PORT OPERATION
The AD9854 serial port configuration bits reside in Bit 1 and
Bit 0 of Register Address 20 hex. It is important to note that the
configuration changes immediately upon a valid I/O update.
For multibyte transfers, writing to this register can occur during
the middle of a communication cycle. The user must compensate
for this new configuration for the remainder of the current com-
munication cycle.
The system must maintain synchronization with the AD9854,
or the internal control logic is not able to recognize further
instructions. For example, if the system sends the instruction to
write a 2-byte register and then pulses the SCLK pin for a 3-byte
register (24 additional SCLK rising edges), communication
synchronization is lost. In this case, the first 16 SCLK rising
edges after the instruction cycle will properly write the first two
data bytes into the AD9854, but the next eight rising SCLK
edges are interpreted as the next instruction byte, not the final
byte of the previous communication cycle.
In the case where synchronization is lost between the system
and the AD9854, the IO RESET pin provides a means to re-
establish synchronization without reinitializing the entire chip.
Asserting the IO RESET pin (active high) resets the AD9854 serial
port state machine, terminating the current I/O operation and
putting the device into a state in which the next eight SCLK rising
edges are understood to be an instruction byte. The IO RESET pin
must be deasserted (low) before the next instruction byte write
can begin. Any information that is written to the AD9854 registers
during a valid communication cycle prior to loss of synchronization
remains intact.
SCLK
SDIO
SDO
SDIO
CS
CS
SYMBOL
t
t
t
t
t
t
INSTRUCTION
INSTRUCTION
PRE
SCLK
DSU
SCLKPWH
SCLKPWL
DHLD
CYCLE
Figure 56. Timing Diagram for Data Write to AD9854
BYTE
Figure 57. Timing Diagram for Read from AD9854
t
t
DSU
PRE
FIRST BIT
t
SCLKPWH
t
MIN
30ns
100ns
30ns
40ns
40ns
0ns
DATA BYTE 1
DHLD
t
SCLK
t
SCLKPWL
DEFINITION
CS SETUP TIME
PERIOD OF SERIAL DATA CLOCK
SERIAL DATA SETUP TIME
SERIAL DATA CLOCK PULSE WIDTH HIGH
SERIAL DATA CLOCK PULSE WIDTH LOW
SERIAL DATA HOLD TIME
DATA TRANSFER
DATA TRANSFER
SECOND BIT
DATA BYTE 2
DATA BYTE 3