2-830613-2 TE Connectivity, 2-830613-2 Datasheet - Page 3

• Manufacturer Part Number: 2-830613-2
• Description: Cable Assembly Lead 0.3556m 16AWG LGH
• Manufacturer: TE Connectivity

Specifications of 2-830613-2

• Connector Type: LGH
• Cable Type: Lead
• Cable Length: 0.356 m
• Product Type: Lead Assembly
• Mount Angle: Straight
• Cap Material: Glass-Filled Epoxy
• Wire Size (mm² [awg]): 16
• Operating Voltage (kvdc): 15
• Shielded: No
• Lead Assembly Type: Single-End
• Assembly Length (mm [in]): 355.60 [14.000]
• Barrel Depth (mm [in]): 22.61 [0.890]
• Positive Stop Ferrule: Without
• Wire Color: White (Standard)
• Cap Color: Green
• Pigtail Length (mm [in]): 9.65 [0.380]
• Wire Diameter (mm [in]): 4.22 [0.166]
• Wire Insulation: Silicone
• Preloaded: Yes
• Rohs/elv Compliance: ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was ELV compliant

Rev O2
Vibration, sinusoidal.
Mechanical shock.
Durability.
Contact engaging force.
Contact separating force.
Therm al shock.
Hum idity, steady state.
Tem perature life.
Test Description
No discontinuities of 10
m icroseconds or longer duration.
See Note.
No discontinuities of 1 m icrosecond
or longer duration.
See Note.
See Note.
20 ounces m axim um .
3 ounces m inim um .
See Note.
See Note.
See Note.
ENVIRONMENTAL
MECHANICAL
Figure 1 (cont)
Requirem ent
EIA-364-28, Test Condition I.
Subject m ated specim ens to 10-55-
10 Hz traversed in 1 m inute with 1.5
m m [.06 in] m axim um total
excursion. 2 hours in each of 3
m utually perpendicular planes.
EIA-364-27, Method H.
Subject m ated specim ens to 30 G's
half-sine shock pulses of 11
m illiseconds duration. 3 shocks in
each direction applied along 3
m utually perpendicular planes, 18
total shocks.
EIA-364-9.
Mate and unm ate gold plated
specim ens for 500 cycles and tin
plated specim ens for 50 cycles at a
m axim um rate of 500 cycles per
hour.
AMP Spec 109-35.
Measure force necessary to
engage using gage 2 to a depth of
.19 inch for 1/2I and 1/2LI and .25
inch for 1I, 1LI, 2I, 3I and 4I.
See Figure 4.
AMP Spec 109-35.
Size 3 tim es using gage 2. Then
insert gage 1 to depth of .19 inch
for 1/2I and 1/2LI and .25 inch for
1I, 1LI, 2I, 3I and 4I and m easure
force necessary to separate.
See Figure 4.
EIA-364-32.
Subject specim ens to 5 cycles
between -55 and 125 C.
EIA-364-31, Method II, Condition A.
Subject specim ens to 40 C and 90
to 95% RH for 96 hours.
EIA-364-17, Method A, Test
Condition 5, Test Tim e Condition A.
Subject m ated specim ens to 125 C
for 96 hours.
Procedure
108-36033
3 of 6