DS3181 Maxim Integrated Products, DS3181 Datasheet - Page 94
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS3181
Manufacturer Part Number
DS3181
Description
Network Controller & Processor ICs DS3-E3 ATM-Packet PH Y with Built-in Line
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3184DK.pdf
(400 pages)
Specifications of DS3181
Product
Framer
Number Of Transceivers
1
Data Rate
44.736 Mbps
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
280 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Package / Case
TEBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 94 of 400
- Download datasheet (4Mb)
Considerations
Select the HDLC Controller connection. The default setting connects it to the DS3/E3 Framers. Setting
PORT.CR1.HDSEL = 1 connects the HDLC Controller to the PLCP framers.
In POS-PHY mode, to select cell processing rather than packet processing, set PORT.CR2.PMCPE = 1.
For best performance of the CLAD to meet jitter requirements across the temperature range, especially @ -40 C,
the following test registers should be set after reset:
Address 0x20B = 0x11
Address 0x20F = 0x11
9.1 Monitoring and Debugging
To determine if the device is receiving a good signal and that the chip is correctly configured for its environment,
check the following status registers.
Receive Loss of Lock – PORT.SR.RLOL – The clock recovery circuit of the LIU was unable to recover the clock
from the incoming signal. This may indicate that the LIU’s master clock does not match the frequency of the
incoming signal. Verify that the CLAD is configured to match the clock input on the CLKA, CLKB, and CLKC pins
(DS3, E3, STS-1). See
Loss of Signal – LINE.RSR.LOS – This indicates that the LIU is unable to recover the clock and data because there
is no signal on the line, or that the signal is attenuated beyond recovery.
Loss of Frame – T3.RSR1.LOF (or E3751.RSR1 or E3832.RSR1) – This indicates that the framer was unable to
synchronize to the incoming data. Verify that the FM bits have been correctly configured for the correct mode of
traffic (DS3, E3 G.751, E3 G.832)
Other helpful techniques diagnose a problem include using Line Loopback and Diagnostic Loopback. These
features help to isolate and identify the source of the problem. Line Loopback will loop the receive input to the
transmit output, eliminating the transmit side input from the equation. Diagnostic Loopback will loop the transmit
output before the LIU to the receive framer, eliminating the analog Receive LIU and the receive side analog
circuitry.
One other potential problem is the Line Encoding/Decoding. The device needs to be configured in the same mode
as the far end piece of equipment. If the far end piece of equipment is transmitting and receiving HDB3/B3ZS
encoded data, the DS318x also must be configured to do the same. This is controlled by the LINE.TCR.TZSD and
the LINE.RCR.RZSD bits.
9.1.1
Check the status registers of the FIFO block. Common indicators to check would be the Transmit Underflow,
Transmit Overflow, and Receive Overflow status bits. These status bits are located in the FIFO.TSRL Register and
the FIFO.RSRL Register.
the FIFO was empty.
A Transmit Overflow indicates that either a start of cell or a start of packet or a short packet was received when the
FIFO was full. Additionally, if additional packet data is received when the FIFO is already full, it will result in an
abort status for the current packet and the Transmit Overflow being declared.
A Receive Overflow occurs when cell data is received while the FIFO is full. In a packet system, the overflow will be
declared when a start of packet or a short packet is received or packet data is received when the FIFO is full
resulting in an abort status for the current packet and the Receive Overflow being declared.
9.1.2
Monitoring the Loss of Cell Delineation in the Cell Processor is recommended to insure proper operation. The LCD
status bit is located in the CP.RSR Register and indicates when an Out of Cell Delineation persists for a
programmed number of cells (set in the CP.RLTC Register).
A Transmit Underflow indicates that the transmit cell processor or packet processor has attempted a read while
Cell/Packet FIFO
Cell Processor
Table
10-11.
94
Related parts for DS3181
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: