LAN9217-MT SMSC, LAN9217-MT Datasheet - Page 41

• Manufacturer Part Number: LAN9217-MT
• Description: Ethernet ICs Hi Perfrm Sngl Chip Ethrnet Contrllr
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9217-MT

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 Mbps, 100 Mbps
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Supply Current (max): 69 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16-bit High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX Support
Datasheet
SMSC LAN9217
3.9.3.2
3.10
PHY REG 0.15
SOURCE
RESET
PHY_RST
nRESET
SRST
POR
Energy Detect Power-Down
This power-down mode is activated by setting the Phy register bit 17.13 to 1. Please refer to
5.5.8, "Mode Control/Status," on page 114
no energy is present on the line, the PHY is powered down, with the exception of the management
interface, the SQUELCH circuit and the ENERGYON logic. The ENERGYON logic is used to detect
the presence of valid energy from 100Base-TX, 10Base-T, or Auto-negotiation signals
In this mode, when the ENERGYON signal is low, the PHY is powered-down, and nothing is
transmitted. When energy is received - link pulses or packets - the ENERGYON signal goes high, and
the PHY powers-up. It automatically resets itself into the state it had prior to power-down, and asserts
the INT7.1 bit of the register defined in
ENERGYON interrupt is enabled, this event will cause an interrupt to the host. The first and possibly
the second packet to activate ENERGYON may be lost. When 17.13 is low, energy detect power-down
is disabled.
The LAN9217 has five reset sources:
Table 3.10
Note 3.11 After any PHY reset, the application must wait until the “Link Status” bit in the PHY’s “Basic
Note 3.12 After a POR, nRESET or SRST, the LAN9217 will automatically check for the presence
Note 3.13 HBI - “Host Bus Interface”, NASR - Not affected by software reset.
Detailed Reset Description
Power-On Reset (POR)
Hardware Reset Input Pin (nRESET)
Soft Reset (SRST)
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
PHY Soft Reset via PHY Basic Control Register (PHY REG 0.15)
PLL
X
X
shows the effect of the various reset sources on the LAN9217's circuitry.
Status Register” (PHY Reg. 1.2) is set before attempting to transmit or receive data.
of an external EEPROM. After any of these resets the application must verify that the EPC
Busy Bit (E2P_CMD, bit 31) is cleared before attempting to access the EEPROM, or
change the function of the GPO/GPIO signals, or before modifying the ADDRH or ADDRL
registers in the MAC.
Note
HBI
3.13
X
X
X
Table 3.10 Reset Sources and Affected Circuitry
REGISTERS
Note 3.13
NASR
X
X
DATASHEET
MIL
X
X
X
Section 5.5.11, "Interrupt Source Flag," on page
for additional information on this register. In this mode when
41
MAC
X
X
X
Note 3.11
PHY
X
X
X
X
EEPROM MAC
Note 3.12
RELOAD
ADDR.
X
X
X
Revision 2.7 (03-15-10)
LATCHED
CONFIG.
STRAPS
117. If the
X
X
Section