NT631C-ST153-EV3 Omron, NT631C-ST153-EV3 Datasheet - Page 50
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
NT631C-ST153-EV3
Manufacturer Part Number
NT631C-ST153-EV3
Description
10.48-ColrDisplay,TFT,Ivy,Eng
Manufacturer
Omron
Datasheet
1.NT-AL001.pdf
(315 pages)
Specifications of NT631C-ST153-EV3
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 50 of 315
- Download datasheet (4Mb)
3-1-3
Installation
Power Supply Connection
Note
Note
1. During work at the panel, take care to ensure that no metal scraps enter
2. The thickness of applicable operation panel is 1.6 mm to 4.8 mm. All fit-
Connect a 24 VDC power supply to the power input terminals.
1. Depending on how the power is switched ON/OFF, the entire system may
2. Carefully check the wiring before switching ON the power.
3. Do not connect AC power to the DC terminals.
4. Use DC power supplies with low voltage fluctuation.
5. Do not perform a dielectric strength test.
6. If complying with EC directives (low voltage directives), the following points
7. When using NT631-ST211(B)-EV2, warm-up time of the power supply
RE S ET
R DA
T R M
R DB
S DA
S DB
CS A
CS B
+ D C
24 V
Fittings at the two (*) positions are not necessary if you do not need it dust
proof and waterproof.
the PT.
tings must be tightened uniformly to a torque of 0.5 to 0.6 N ⋅ m in order to
ensure water- and dust-resistance. Front sheet of NT631/NT631C may be
warped if the tightening is too strong or not uniformity. The panel must not
be soiled or warped, and must be able to support an installation that will
remain secure and strong.
stop. Follow the correct procedure when switching the power ON/OFF.
must be noted (compliance with EC directives):
a. Use a power supply with reinforced insulation.
b. When installing NT631-ST211(B)-EV2 on the ultimate system, the
must be 200 ms or less. If longer than this, NT631 may not boot up.
rear of the NT631 must be placed within an enclosure to restrict the
operators’ use only to the front panel.
(:)
(:)
PRINTER
PORT B
24 VDC
PORT A
24 VDC
power supply
Breaker
Section 3-1
33
Related parts for NT631C-ST153-EV3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NT631C-CFL01](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
NT631-ST151 BACKLIGHT
Manufacturer:
Omron
Datasheet:
![NT631C-CFL02](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
NT631-ST141 BACKLIGHT
Manufacturer:
Omron
Datasheet:
![NT631C-CN321-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
3M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
![NT631C-CN322-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
3M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
![NT631C-CN511-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
50CM 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
![NT631C-CN512-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
50CM 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
![NT631C-CN521-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
5M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
![NT631C-CN522-EU](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
5M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
![NT631C-ST153B-EV3](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
10.48-ColrDisplay,TFT,Blk,Eng
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: