NSH5-232CW-3M Omron, NSH5-232CW-3M Datasheet - Page 87
NSH5-232CW-3M
Manufacturer Part Number
NSH5-232CW-3M
Description
HMI
Manufacturer
Omron
Datasheet
1.NSH5-232UL-3M.pdf
(122 pages)
Specifications of NSH5-232CW-3M
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 87 of 122
- Download datasheet (3Mb)
5-3
When a Project Is Newly
Created
During System Setup
5-4
Error Message Tables
Error Message Tables
Precautions When Replacing the PT
If a fault is discovered in the inspection and the PT must be replaced, observe
the following precautions.
If the PT is to be returned to OMRON for repair, attach a document to the PT
describing the problem in as much detail as possible, and send the PT to an
OMRON representative listed at the end of the manual.
The combination of
the selected PT
model and system
version is invalid.
There is an error in
the communications
address input format.
$SB cannot be spec-
ified.
$SW cannot be
specified.
Specify a PT mem-
ory address.
The combination of
the selected PT
model and system
version is invalid.
• Before replacing the PT, back up all of the PT’s project data. If the PT is
• Before replacing the PT, be sure to turn OFF the power supply.
• After replacing the PT, check to be sure that there are no errors in the new
Error message
Error message
repaired by OMRON, the project data may be deleted.
PT.
An attempt was made to
select a version not supported
by NSH5-SQ
An illegal address or other
than a bit address has been
set for the key status monitor
address (emergency stop,
function switches F3, F4, F5,
F8, F9, F10).
An illegal address or other
than a word address has been
set for the station status moni-
tor address.
$SB was specified for the sta-
tion status monitor address.
$SW was specified for the sta-
tion status monitor address.
An address not in the PT
memory was specified for the
station status monitor
address.
An attempt was made to con-
vert a project that is being
edited to a PT model that is
not supported.
Contents
Contents
@
-V2.
Select a version to match the
PT.
Check the key status monitor
address and correct the
address that was set.
Check the station status moni-
tor address and correct the
address that was set.
Set an address other than
$SB.
Set an address other than
$SW.
Check the station status moni-
tor address and set an
address in the PT memory.
Select a version that matches
the PT model.
Countermeasure
Countermeasure
Section 5-3
65
Related parts for NSH5-232CW-3M
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
10m RS232 Cable For NSH5
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
3m RS232 Cable For NSH5
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
10m RS422 Cable For NSH5
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Handheld NS5 W/Grey E-stop,60M
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Handheld NS5 W/Red E-stop,60M
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Removal Box
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
HMI
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: