MTCBA-G2-EN2-GP Multi-Tech Systems, MTCBA-G2-EN2-GP Datasheet - Page 26

• Manufacturer Part Number: MTCBA-G2-EN2-GP
• Description: ROUTER WIRELESS QUAD GPRS GPS
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® rCellr

Specifications of MTCBA-G2-EN2-GP

• Function: Transceiver, GPRS, Router
• Modulation Or Protocol: GSM, GPRS
• Frequency: 850MHz, 900MHz, 1.8GHz, 1.9GHz, 1575.42MHz
• Applications: General Purpose
• Interface: RJ-45, RS-232
• Sensitivity: -161dB
• Voltage - Supply: 9 V ~ 32 V
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 881-1087

Chapter 4 – Using the Web Management Software
General Configuration
Date and Time:
The system date and time display in these formats: MM/DD/YYYY / HH:MM:SS. A real time clock is part of
SNTP to display proper time.
IP Configuration
Enter the following addresses for the Ethernet interface.
IP Address (Default = 192.168.2.1), Mask (Default 255.255.255.0), Default Gateway (Default 0.0.0.0),
Primary DNS (Default 0.0.0.0), Secondary DNS (Default 0.0.0.0).
Note:
See Appendix A – Table of Commonly Supported Subnets.
Auto Dial out Configuration
Auto Dialout:
Check the box to enable/disable Auto Dialout. Default = Enable. The Auto Dialout settings allow you to use the
integrated cellular modem directly with no router functionality. This is accomplished using redirector software on your pc. This
software creates a virtual serial port allowing your pc to communicate with the integrated cellular modem over IP using telnet.
Raw Dialout:
Check the box to enable/disable raw mode for an Auto Dialout session. Default = Disable.
Auto Dialout Login:
Check the box to enable or disable Auto Dialout Login feature. Default = Enable. The Auto Dialout port is
the telnet port used by the redirector software on your pc to communicate to the integrated cellular modem.
Auto Dialout Port:
Enter the serial Auto Dialout Port number. Default = 5000.
Handle EIA Signal:
Check the box to enable/disable the EIA standard signal characteristics (time and duration) used between
different electronic devices.
Inactivity:
Enter the time in seconds that the auto dialout session will stay active before going inactive.
Syslog Configuration
Syslog:
Check the box to enable or disable Syslog. Default = Disable.
Syslog Server IP Address:
If a Remote Syslog Server IP Address is specified, the syslog feature acts as a remote Syslog.
Auto Discovery
Auto Discovery:
Check the box to enable or disable Auto Discovery to broadcast (MAC level), the MAC Address, IP Address,
and DHCP information to the configured server port. Default = Enable. The router will send a broadcast packet on the specified
server port every 10 seconds or whatever interval the broadcast timer is set to.
Server Port:
Enter the Server Port Number. Default port is 1020.
Broadcast Timer:
Enter the amount of time in seconds for the auto-discovery packet granularity of periodic broadcasting.
Default is 10 seconds.
Auto Reboot Timer Configuration
Auto Reboot Timer:
Enter the number of hours to lapse between each automatic reboot. The default of zero deactivates the
timer. Range is 0 to 999.
Telnet Configuration
Enables/Disables the Telnet port. The default is Enable. This is specifically for telnet port 23 for technical support debug. You
can still access the integrated cellular modem using port 5000 when this is disabled. Ensure that PPP is also disabled before
telnetting to the port.
Submit Button
Click the Submit button to save these settings.
Note:
You must click Save and Restart once you have completed and submitted all the screens on which you have made
changes.
26
Multi-Tech Systems, Inc. MultiModem rCell User Guide