KSZ8893MQL Micrel Inc, KSZ8893MQL Datasheet - Page 62

• Manufacturer Part Number: KSZ8893MQL
• Description: IC,Telecom Switching Circuit,CMOS,QFP,128PIN,PLASTIC
• Manufacturer: Micrel Inc

Specifications of KSZ8893MQL

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• Number Of Primary Switch Ports: 3
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1603 - EVAL KIT EXPERIMENTAL KSZ8893MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1477-5

Register 1 (0x01): Chip ID1 / Start Switch
Register 2 (0x02): Global Control 0
Bit
7-4
3-1
0
Bit
7
6-4
3
2
1
0
December 2007
Name
Chip ID
Revision ID
Start Switch
Name
New Back-off
Enable
Reserved
Pass Flow
Control Packet
Reserved
Reserved
Link Change
Age
R/W
RO
RO
RW
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
0x2 is assigned to M series. (93M)
Revision ID
= 1, start the chip when external pins
Note: In (PS1, PS0) = (0, 0) mode, the chip will start
automatically after trying to read the external
EEPROM. If EEPROM does not exist, the chip will
use pin strapping and default values for all internal
registers. If EEPROM is present, the contents in the
EEPROM will be checked. The switch will check: (1)
Register 0 = 0x88, (2) Register 1 bits [7:4] = 0x2. If
this check is OK, the contents in the EEPROM will
override chip registers’ default values.
= 0, chip will not start when external pins
Description
New back-off algorithm designed for UNH
Reserved
Do not change the default value.
= 1, switch will not filter 802.1x “flow control” packets
Reserved
Do not change the default value.
Reserved
Do not change the default value.
= 1, link change from “link” to “no link” will cause fast
aging (<800us) to age address table faster. After an
age cycle is complete, the age logic will return to
normal aging (about 200 sec).
Note: If any port is unplugged, all addresses will be
automatically aged out.
(PS1, PS0) = (0,1) or (1,0) or (1,1).
1 = Enable
0 = Disable
(PS1, PS0) = (0,1) or (1,0) or (1,1).
62
Default
0x2
-
-
Default
0
100
0
1
0
0
M9999-121007-1.5