ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 76

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ADuC7060/ADuC7061
Table 84. PWMCON MMR Bit Designations
Bit
15
14
13
12
11
10
9
8:6
5
4
3
2
1
0
1
In H-bridge mode, HMODE = 1. See Table 85 to determine the PWM outputs.
Name
Reserved
Sync
PWM5INV
PWM3INV
PWM1INV
PWMTRIP
ENA
PWMCP[2:0]
POINV
HOFF
LCOMP
DIR
HMODE
PWMEN
This bit is reserved. Do not write to this bit.
If HOFF = 0 and HMODE = 1. Note that, if not in H-bridge mode, this bit has no effect.
PWM clock prescaler bits. Sets the UCLK divider.
Load compare registers.
Direction control.
Set to 1 by user to enable all PWM outputs.
Description
Enables PWM synchronization.
Set to 1 by user so that all PWM counters are reset on the next clock edge after the detection of a high-to-low
transition on the P1.2/SYNC pin.
Cleared by user to ignore transitions on the P1.2/SYNC pin.
Set to 1 by user to invert PWM5.
Cleared by user to use PWM5 in normal mode.
Set to 1 by user to invert PWM3.
Cleared by user to use PWM3 in normal mode.
Set to 1 by user to invert PWM1.
Cleared by user to use PWM1 in normal mode.
Set to 1 by user to enable PWM trip interrupt. When the PWM trip input (Pin P1.3/TRIP) is low, the PWMEN bit is
cleared and an interrupt is generated.
Cleared by user to disable the PWMTRIP interrupt.
Set to 1 by user to enable PWM outputs.
Cleared by user to disable PWM outputs.
If HOFF = 1 and HMODE = 1, see Table 85.
[000] = UCLK/2.
[001] = UCLK/4.
[010] = UCLK/8.
[011] = UCLK/16.
[100] = UCLK/32.
[101] = UCLK/64.
[110] = UCLK/128.
[111] = UCLK/256.
Set to 1 by user to invert all PWM outputs.
Cleared by user to use PWM outputs as normal.
High side off.
Set to 1 by user to force PWM0 and PWM2 outputs high. This also forces PWM1 and PWM3 low.
Cleared by user to use the PWM outputs as normal.
Set to 1 by user to load the internal compare registers with the values in PWMxCOMx on the next transition of the
PWM timer from 0x00 to 0x01.
Cleared by user to use the values previously stored in the internal compare registers.
Set to 1 by user to enable PWM0 and PWM1 as the output signals while PWM2 and PWM3 are held low.
Cleared by user to enable PWM2 and PWM3 as the output signals while PWM0 and PWM1 are held low.
Enables H-bridge mode.
Set to 1 by user to enable H-bridge mode and Bit 1 to Bit 5 of PWMCON.
Cleared by user to operate the PWMs in standard mode.
Cleared by user to disable all PWM outputs.
1
Rev. C | Page 76 of 108