BLM15AG221PN1D Murata, BLM15AG221PN1D Datasheet - Page 176

• Manufacturer Part Number: BLM15AG221PN1D
• Manufacturer: Murata
• Type: EMI Filterr

Specifications of BLM15AG221PN1D

• Mounting Style: Surface Mount
• Termination: Flat Style
• Operating Temp Range: -55C to 125C
• Current Rating (max): 0.3A
• Product Height (mm): 0.5mm
• Product Depth (mm): 0.5mm
• Product Length (mm): 1mm
• Lead Free Status / RoHS Status: Compliant

6
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
174
EMIFILr (Soldering and Mounting)
DLM11G
DLM2HG
DLP0NS
DLP11S
DLP1ND
DLP2AD
DLP31S
DLP31D
DLW21S
DLW21H
DLW31S
DLW5AH
DLW5BS
DLW5BT
NFE61P
NFE61H
Continued from the preceding page.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Chip mounting side
o Reflow Soldering
oReflow and Flow
oReflow Soldering
DLP0NS
2.0
4.8
8.8
DLW5AH/5BS/5BT
0.30
0.90
DLM11G
Small diameter thru hole ø0.4
(2)
(3)
1.5
0.5
DLM2HG
0.9
2.9
5.5
1.0
4.0
(1)
(4)
DLW21S/21H/31S
*(1), (2), (3), (4): Terminal Number
a
b
3
DLP11S
0.55
1.95
DLP31S
1.0 0.6 1.0
Do not use gild pattern; excess soldering heat may dissolve
metal of a copper wire.
Chip mounting side
o Flow Soldering (Except NFE61HT332)
1: If the pattern is made with wider than 1.2mm (DLW21) /
2: If the pattern is made with less than 0.4mm, in the worst
3: If the pattern is made with wider than 0.8mm (DLW21) /
DLW21S/H
DLW31S
1.6mm (DLW31S) it may result in components turning
around, because melting speed is different. In the worst
case, short circuit between lines may occur.
case, short circuit between lines may occur due to spread
of soldering paste or mount placing accuracy.
1.6mm (DLW31S), the bending strength will be reduced.
Series
Small diameter thru hole ø0.4
1.5
3.8
4.8
9.0
0.4
DLP1ND
0.2
1.4
0.8
1.6
a
Continued on the following page.
2.6
3.7
b
0.8 pitch
Land Pattern
+ Solder Resist
Land Pattern
Solder Resist
DLP31D
0.5
0.25
DLP2AD
0.4
0.4
2.8
c
1.75
0.4
1.2
1.6
d
(in mm)
C31E.pdf
07.8.31