BLM15AG221PN1D Murata, BLM15AG221PN1D Datasheet - Page 171

• Manufacturer Part Number: BLM15AG221PN1D
• Manufacturer: Murata
• Type: EMI Filterr

Specifications of BLM15AG221PN1D

• Mounting Style: Surface Mount
• Termination: Flat Style
• Operating Temp Range: -55C to 125C
• Current Rating (max): 0.3A
• Product Height (mm): 0.5mm
• Product Depth (mm): 0.5mm
• Product Length (mm): 1mm
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
1. Self-heating
2. Mounting Direction
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
<Storage and Handling requirements>
1. Storage Period
1. Washing
2. Soldering
1. Resin coating
Using resin for coating/molding products may affect
the products performance.
So please pay careful attention in selecting resin.
Prior to use, please make the reliability
evaluation with the product mounted in your
application set.
!Caution (Rating)
!Caution (Soldering and Mounting)
Notice (Storage and Operating Conditions)
BLM (except BLM15E/15H series) /BLA/NFM55/DLP31S/
DLM11G/DLM2HG series should be used within 6
months, the other series should be used within 12
months.
Solderability should be checked if this period is
exceeded.
Notice (Soldering and Mounting)
Failure and degradation of a product are caused
by the washing method. When you wash in conditions
that are not in mounting information, please contact
Murata engineering.
Reliability decreases with improper soldering
methods. Please solder by the standard soldering
conditions shown in mounting information.
Notice (Handling)
Please provide special attention when mounting chip
"EMIFIL" (BLM_P/S, NFM_P) series in close proximity to
other products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in this
component.
Mount Chip Common Mode Choke Coils in right direction.
Wrong direction, which is 90 degrees rotated from right
direction, causes not only open or short circuit but also
flames or other serious trouble.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Storage Conditions
3. Other
2. Caution for use (DLW Series)
When you hold products with a tweezer, please hold by
the sides. Sharp materials, such as a pair of tweezers,
should not touch the winding portion to prevent breaking
the wire. Mechanical shock should not be applied to the
products mounted on the board to prevent breaking the
core.
(1) Storage temperature: -10 to 40 degrees C
(2) Do not store products in a chemical atmosphere
Noise suppression levels resulting from Murata's
EMI suppression filters "EMIFIL" may vary,
depending on the circuits and ICs used, type of
noise, mounting pattern, lead wire length, mounting
location, and other operating conditions. Be sure
to check and confirm in advance the noise
suppression effect of each filter, in actual
circuits, etc. before applying the filter in a
commercial-purpose equipment design.
Relative humidity: 30 to 70%
Avoid sudden changes in temperature and
humidity.
such as chlorine gas, acid or sulfide gas.
right direction
Chip EMIFILr !Caution/Notice
Z
wrong direction
Z
169
C31E.pdf
07.8.31
6