E3G-L77 Omron, E3G-L77 Datasheet

Page 1

... Connector white card white card Terminal Terminal block Conductors Three 2 E3G Timer function Part number —— E3G-R13 E3G-R17 E3G-MR19- OFF E3G-MR19T-US delay 0- - 5s, adjustable —— E3G-L73 E3G-L77 E3G-ML79- OFF E3G-ML79T-US delay 0- - 5s, adjustable Part number XS2F-D421-DC0-A XS2F-D421-GC0-A XS2F-D422-DC0-A XS2F-D422-GC0-A ...

Page 2

... Applicable model Pre-leaded and connector models E3G-R1j E3G-L7j Terminal block models E3G-MR19 (T) E3G-ML79 (T) E3G-MR19 (T) E3G-ML79 (T) Remarks Part number Included with E3G-Rjj and E39-R2 E3G-MRjj E39-R1 --- Remarks Part number Provided with rubber bushing and cap E39-L129 for pullout prevention in vertical direction Remarks ...

Page 3

... Protection from mutual Protection from reversed interference power supply connection, load short-circuit, and mutual interference (This table continues on the next page.) 4 E3G E3G-L77 E3G-ML79 E3G-ML79T --- 12 to 240 VDC ±10% including 10% (p-p) max. ripple 24 to 240 VAC ±10% at 50/ max. ...

Page 4

... Stainless steel (SUS304), order separately bracket Engineering Data J RETROREFLECTIVE MODELS, E3G-R/MR Lateral Movement E39-R2 Reflector Distance X (m) Diffuse E3G-MR19 E3G-MR19T E3G-L73 E3G-L77 30 ms max Teaching (in NORMAL or ZONE mode) 2,000 VAC, 50/60 Hz for 1,000 VAC, 50/60 Hz for 1 min 1 min Terminal block 2 m cable ...

Page 5

... E3G J DIFFUSE MODELS, E3G-L/ML Spot Diameter vs. Sensing Distance Horizontal Vertical Distance (m) Sensing Object Size vs. Setting Distance White paper Black paper 0.5 m Side length (one side) of sensing object: d (mm) Sensing Distance vs. Sensing Object Material (at 1-m Setting Distance) Material Sensing Zone in NORMAL Mode Distance setting: 0 ...

Page 6

... E3G Operation J OUTPUT CIRCUITS NPN/PNP Selectable Part number E3G-R13 E3G-R17 E3G-L73 E3G-L77 Output Light ON transistor status Timing chart Received Not received Operation ON indicator OFF (orange) ON Output transistor OFF Operate Load (relay) Reset Output NPN configuration Output circuit PNP output transistor NPN or PNP ...

Page 7

... Operation ON indicator OFF (orange OFF Mode selector Light-ON (L/ON) Timer function ON or OFF delay (adjustable) Part number E3G-MR19T E3G-ML79T Timing chart Incident Interrupted ON ON delay OFF ON OFF delay OFF Mode selector Light-ON (L/ON) Output circuit Main circuit Note: Td1, Td2: Delay time ( ...

Page 8

... Sensitivity adjuster Note: The ON- or OFF-delay adjuster is not available with the E3G-MR19. Diffuse E3G-L73 (Pre-leaded Model) E3G-L77 (Connector Model) Stability indicator (Green) Teaching indicator (Red and green) PNP/NPN selector NORMAL/ZONE selector Note: The ON- or OFF-delay adjuster is not available with the E3G-ML79. ...

Page 9

... Tensile strength E3G-R13, E3G-MR19( max. E3G-R17 10 N max. J ADJUSTMENTS Indicators The following illustration indicates the operation levels of the E3G. Set the E3G so that it will work within the stable operation range. Operation indicator (orange) Stability indicator (green Stable operation ON range (see note) Operation level x 1 ...

Page 10

... Install the Sensor as shown in the following if each sensing object greatly differs in color or material. Correct J OTHERS If a teaching data error occurs with the operation indicator flashing due to a power failure or static noise, perform the teaching operation of the Sensor again. Sensing object 11 Incorrect Moving direction Moving direction E3G ...

Page 11

... If the teaching is successful, set the mode selector to RUN to complete the teaching operation. Set the E3G to light- ordark-ON mode with the mode selectoraccording to the application. If the teaching is not successful, change the set distance and object sensing position and repeat two-point teaching from step 3. ...

Page 12

... Attach the E39-L129 Terminal Protection Cover for side-pull- out cable. 3. Remove the clamping nut, washer, and rubber bushing of the E3G. These are used for the side-pullout cable. 4. Attach the rubber bushing and cap provided with the E39-L129 to the E3G as replacements. Terminal ...

Page 13

... Two, 4.5-dia. mounting holes 84.45 84.95 (3.34 (1.46) 16 (0.63) 68 (2.68) 44 1/2-14 NPT (1.73) conduit entrance 14 E3G-R17 and E3G-L77 Connector Models Note: All dimensions other than the ones specified below are the same as the corresponding di- mensions of E3G-R13 M12 Connector Mounting holes Two, M4 ...

Page 14

... Reflectors Four, 3.5 dia. E39-R2 59.9 (2.36) Material Surface: Acrylic resin Backside: ABS resin Note: Supplied with E3G-Rjj, E3G-MRjj, and E3G-MRjj-US. E39-R1 Two, 3.5 dia. Material Surface: Acrylic resin Backside: ABS resin J MOUNTING BRACKETS (NOT INCLUDED, ORDER SEPARATELY) Two, R3.2 E39-L131 90° ...

Page 15

... J CONNECTOR CORDSETS Straight XS2F-D421-DC0-A (L=2 m) XS2F-D421-GC0-A (L dia. Right angle XS2F-D422-DC0-A (L=2 m) XS2F-D422-GC0-A (L=5 m) E39-L136 Two, R3.2 Two, 4.2 dia. Two, R3.2 45° M12 14.9 dia. 40.7 25.3 6 dia. 28.3 M12 5 dia. 45° 16 Material: Stainless steel (SUS304) Two, R3.2 6 dia E3G Fourteen, R2.1 ...

Page 16

... The E3G has a built-in function to protect the Sensor from load short-circuiting. If load short-circuiting results, the output will be turned OFF. In that case, check the wiring and turn ON the E3G again so that the short-circuit protection circuit will be reset. This function will operate if the output current flow is at least 2.0 times the rated load current ...

Page 17

... OMRON ELECTRONICS LLC One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. CEDSAX4 11/01 OMRON ON- -LINE Global -- http://www.omron.com USA -- http://www.omron.com/oei Canada -- http://www.omron.com/oci Specifications subject to change without notice. E3G OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 416-286-6465 Printed in U.S.A. ...