E3G-L77 Omron, E3G-L77 Datasheet
E3G-L77
Specifications of E3G-L77
Related parts for E3G-L77
E3G-L77 Summary of contents
Page 1
... E3G-ML79(T) CSM_E3G_DS_E_3_1 Red light Infrared light Model Timer NPN/PNP function Relay output selector E3G-R13 2M --- --- E3G-R17 E3G-MR19 --- Yes E3G-MR19T E3G-L73 2M --- --- E3G-L77 E3G-ML79 --- Yes E3G-ML79T Remarks Provided with the E3G-R1@/MR19(T). --- Remarks Provided with rubber bushing and cap for pullout prevention in vertical direction. 1 ...
Page 2
... Straight Standard L-shaped Note: Refer to Introduction to Sensor I/O Connectors for details. Quantity Applicable model 1 E3G-R1@ E3G-L7@ 1 Rear-mounting use 1 Cable pulled out in the downward direction E3G-MR19(T) E3G-ML79(T) 1 Cable type Model 2 m XS2F-D421-DC0-A Three XS2F-D421-GC0-A conductor 2 m XS2F-D422-DC0-A type 5 m XS2F-D422-GC0-A E3G Remarks --- --- 2 ...
Page 3
... VAC, 50/60 Hz for 1 min 2,000 VAC, 50/60 Hz for 1 min. Pre-wired Terminal block (Standard length Approx. 150 g Adjustment screwdriver and Instruction manual E3G Distance-setting E3G-L77 E3G-ML79 E3G-ML79T --- --- 12 to 240 VDC±10%, ripple (p-p): 10% max 240 VAC±10 max. Relay output: SPDT (cosφ ...
Page 4
... Engineering Data (Typical) E3G-R/MR Retro-reflective Models Excess Gain vs. Set Distance 500 E39-R2 Reflector 100 10 Operating level 1 0 Distance (m) E3G-L/ML Distance-setting Models Spot Diameter vs. Sensing Distance 120 Horizontal Vertical 100 0.5 1 1.5 2 2.5 Distance (m) Sensing Object Size vs. Setting Distance 3 White paper Distance setting: 0.5, 1, and 2 m Black paper 2 ...
Page 5
... Incident light No incident light Operation indicator Light-ON (orange) Output transistor Operate Load (relay) E3G-R13 Reset E3G-R17 E3G-L73 E3G-L77 Incident light No incident light Operation indicator Dark-ON (orange) Output transistor Operate Load (relay) Reset Sensing Distance vs. Sensing Object Material (at 1-m Setting Distance) 1 ...
Page 6
... Wire color Classifi- Wire Connector cation color pin No. Brown Blue Brown 1 Black --- 2 DC Blue 3 Black 4 Note: Pin 2 is not used. E3G Output circuit Contact output (G6C Relay built in Photo 240 VAC or electric Power 12 to 240 VDC Sensor supply main (no polarity restriction) ...
Page 7
... Sensitivity adjuster ON-delay adjuster * OFF-delay adjuster * * The ON- or OFF-delay adjuster is not available with the E3G-MR19. Distance-setting E3G-L73 (Pre-wired Model) E3G-L77 (Standard Connector Model) Stability indicator (Green) Teaching indicator (Red and green) Operation indicator (Orange) Output selector Output selector Operation selector NORMAL/ZONE ...
Page 8
... The tensile strength of the cable during operation should not exceed the values shown below. Tensile strength Model (torque) E3G-L73 50 N max. E3G-ML79(T) E3G-L77 10 N max. ● Mounting Mounting Mounting Directions • Make sure that the sensing side of the Sensor is parallel with the surface of each sensing object. Do not incline the Sensor towards the sensing object ...
Page 9
... The E3G has a built-in function to protect the E3G from load shortcircuiting. If load shortcircuiting results, the output will be turned OFF. In that case, check the wiring and turn ON the E3G again so that Terminal protection cover the short-circuit protection circuit will be reset. This function will operate if the output current flow is at least 2 ...
Page 10
... Standard Connector Model E3G-R17 Note: All dimensions other than the ones specified below are the same as the corresponding dimensions of E3G-R13 M12 Connector 10.5 dia. 43 *The ON- or OFF-delay adjuster is not available with the E3G-MR19. Mounting Holes Two Hexagonal nut (Diagonal: 22) Applicable cable dia. 10 ...
Page 11
... ON-delay adjuster* 14 M2.6 nut 18 84.95 84. Standard Connector Model E3G-L77 Note: All dimensions other than the ones specified below are the same as the corresponding dimensions of the E3G-L73 M12 Connector 10.5 dia. 43 *The ON- or OFF-delay adjuster is not available with the E3G-ML79. ...
Page 12
... Refer to page 9 for the mounting method of the product. Reflectors Refer to E39-L/F39-L/E39-S/E39-R for details. Mounting Brackets Refer to E39-L/F39-L/E39-S/E39-R for details. Sensor I/O Connectors Refer to Introduction to Sensor I/O Connectors for details. Terminal Protection Cover for Side-pullout Cable (Example: E3G-MR19) M2.6 61 E3G M2.6 Hexagonal nut (Diagonal: 22) Applicable cable dia ...
Page 13
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...