GP1UE261RKVF Sharp Microelectronics, GP1UE261RKVF Datasheet - Page 5
![Infrared Receivers Rem Cont Receiver 3V 38 kHz](/photos/40/17/401704/gp1ue261rkvf_sml.jpg)
GP1UE261RKVF
Manufacturer Part Number
GP1UE261RKVF
Description
Infrared Receivers Rem Cont Receiver 3V 38 kHz
Manufacturer
Sharp Microelectronics
Datasheet
1.GP1UE26RK0VF.pdf
(6 pages)
Specifications of GP1UE261RKVF
Carrier Frequency
38 KHz
High Level Pulse Width
1200 us
Low Level Pulse Width
1000 us
Minimum High Level Output Voltage
2.2 V
Operating Voltage
2.7 V to 5.5 V
Supply Current
0.27 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
- 10 C
Sensing Distance
10m
B.p.f. Center Frequency
38.0kHz
Voltage - Supply
2.7 V ~ 5.5 V
Current - Supply
400µA
Orientation
Top View
Mounting Type
Through Hole
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GP1UE261RKVF
Manufacturer:
SHRP
Quantity:
5 975
7. To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
■ Precautions for Operation
1. When this infrared remote control detecting unit shall be adopted for wireless remote control, please use the following signal format .
(NEC code,RC-6code etc.)
2. Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics, operating conditions of
3. Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
4. The shield case should be grounded on PCB pattern.
5. Do not apply unnecessary force to the terminal and the case.
6. Do not push the light detector surface (photodiode) from outside.
8. Do not use hole and groove set in the case of the light detecting unit for other purposes, since they are required to maintain the
9. External Circuit Examples (Mount the outer parts as near the unit as possible).
・ON signal time and OFF signal time
・Total duty ratio D
The circuit constant is a example. It is difference from mounting equipment. Please select it by your mounting equipment.
This device has a transistor as protection element between V
Please be carefully not to apply exceeding the absolute maximum ratings of applying voltage and continuous high voltage spike
noise because there is cases that transistor will be short by secondary breakdown generally. In order to do difficultly, Please add CR
filter(47Ω(1/10W), 10μF or more)such as external circuit example above near V
In setting R
Care must be taken not to touch the light detector surface.
(The area across the shield case and the GND terminal is internally non-conductive.)
If it should be dirty, wipe off such dust and refuse with soft cloth so as to prevent scratch. In case some solvents are required, use
methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the
function, fading of markings such as the part number.
light emitting device and the characteristics of the light detecting unit.
specified performance.
In case the signal format of total duty and/or ON/OFF signal time dosen`t meet the conditions noted above, there is a
case that reception distance much reduces or output dose not appear.
1
and C
1
t
, use suitable values after considering under the real condition
(Emitting time t
t
1
OFF signal time per 1bit
ON signal time per 1bit
Supply Voltage
GND
V
V
CC
OUT
Σ
N=1
n
t
2
N
/ Transmitting time for 1 block T) : 40% or less.
C
Transmitting time for 1 block:T
O
+
t
3
D
t
=(
N=1
Σ
n
R
t
1
N
/T) ×100 (%)
t
V
t
ON
OFF
cc
CC
and GND to improve anti-static electricity proof.
5
GND
V
V
400μs or more
e
O
2.7 to 3.0V
200μs or more
(Circuit parameters)
R
C
1=
1=
GP1UE26RK0VF/GP1UE27RK0VF Series
GP1UE28RK0VF/GP1UE28QK0VF Series
47Ω±5%
47μF
CC
T
.
t
ON
n
300μs or more
3.0 to 5.5V
Sheet No.: OP06006