LQ104V1DG61 Sharp Microelectronics, LQ104V1DG61 Datasheet - Page 10

TFT Displays & Accessories 10.4 VGA STG 2

LQ104V1DG61

Manufacturer Part Number
LQ104V1DG61
Description
TFT Displays & Accessories 10.4 VGA STG 2
Manufacturer
Sharp Microelectronics
Datasheet

Specifications of LQ104V1DG61

Diagonal
10.4 in
Viewing Area (w X H)
211.2 mm x 158.4 mm
Pixel Density
640 x 480
Module Size (w X H X T)
246.5 mm x 179.4 mm x 13.7 mm
Backlighting
White
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LQ104V1DG61
Manufacturer:
HITACHI
Quantity:
1 000
Part Number:
LQ104V1DG61
Quantity:
11
7-2. Backlight driving
[Note2] Referential data per one CCFT by calculation. (I L
[Note3] Lamp frequency may produce interference with horizontal synchronous frequency,and this may cause
[Note4] The open output voltage of the inverter shall be maintained for more than 1s; otherwise
[Note5] Above value is applicable when lamp (the long side of LCD module) is placed horizontally.
[Note6] The performance of the backlight, for example life time or brightness, is much influenced
[Note7] It is required to have the inverter designed so that to allow the impedance deviation of the two CCFT lamps
[Note8] Under the environment of 10lx or less, miss-lighting delay may occur.
[Note1] Lamp current is measured with current meter for high frequency as shown below.
Parameter
Lamp current
Lamp power consumption
Lamp frequency
Kick-off voltage
Lamp life time
The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube).
The characteristics of single lamp are shown in the following table.
(It is usually required to measure under the following condition.
Module
condition:IL=6.0mA,Ta=25
The data don’t include loss at inverter. ( IL=6.0mArms)
beat on the display. Therefore lamp frequency shall be detached as much as possible from the horizontal
synchronous frequency and from the harmonics of horizontal synchronous to avoid interference.
the lamp may not be turned on.
(Landscape position)
Lamp life time is defined that it applied either
(Lamp lifetime may vary if lamp is in portrait position due to the change of mercury density inside the lamp.)
In case of operating under lower temp environment, the lamp exhaustion is accelerated
and the capacity deviation of barast capacitor.
Recommended inverter is “CXA-0454(TDK)”.
(“CXA-P1212B-WJL(TDK)” is also recommended general temperature condition. )
and the brightness becomes lower.
(Continuous operating for around 1 month under lower temp condition may reduce the
In case of such usage under lower temp environment, periodical lamp exchange is recommended.
by the characteristics of the DC-AC inverter for the lamp. When you design or order the
inverter, please make sure that a poor lighting caused by the mismatch of the backlight and
the inverter (miss-lighting,flicker, etc.) never occur. when you confirm it, the module should
be operated in the same condition as it is installed in your instrument.
Be sure to use a back light power supply with the safety protection circuit such as the detection circuit
for the excess voltage, excess current and or electric discharge waveform.
Be sure to use the detect circuit by which one side of the CCFT lamps can be controlled
independently. Otherwise, when one side of the CCFT is open, the excess current may possibly
be applied to the other side of the lamp.
(Continuous turning on at Ta=25
brightness to half of the original brightness.)
Brightness becomes 50% of the original value under standard condition.
Kick-off voltage at Ta=-30
CN2,3: 1pin
CN2,3: 2pin
Symbol
PL
FL
Vs
LL
IL
2 ,FL=60kHz.)
o
C exceeds maximum value, 1300Vrms.
50000
60000
o
Min.
C, IL=6.0mA rms)
3.0
35
-
-
-
Typ.
6.0
2.8
60
-
-
-
-
Inverter
output voltage
or
(2000)
VL)
Max.
1300
6.5
70
-
-
-
under this condition
mA rms
V rms
Hour
Hour
Unit
kHz
W
at barast capacitor=12pF
Transformer output
Transformer
output voltage
Inverter
Inverter output
IL=6.0mArms [Note5]
IL=5.0mArms [Note5]
Remark
[Note1]
[Note2]
[Note3]
Ta=-30
[Note4]
o
C

Related parts for LQ104V1DG61