LQ104S1LG21 Sharp Microelectronics, LQ104S1LG21 Datasheet
LQ104S1LG21
Specifications of LQ104S1LG21
Related parts for LQ104S1LG21
LQ104S1LG21 Summary of contents
Page 1
Feb 18203A 6 ...
Page 2
...
Page 3
Feb ...
Page 4
... Application This specification applies to color TFT-LCD module, LQ104S1LG21 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a backlight unit. Graphics and texts ...
Page 6
Input Terminals 4-1. TFT-LCD panel driving CN1 (LVDS Signals , +3.3V DC power supply and Contorol signal) Corresponding connector:FI-SE20ME (FPC Type) or FI-S20S (WireType) Pin No. Symbol GND 4 GND 5 RXIN0- ...
Page 7
Signal Signal LVDS →Digital Signal LVDS Signal Digital → LD18203A-4 ...
Page 8
Data Mapping 4-3. Backlight driving CN2 ,CN3 Used connector : BHR-03VS-1(JST) Corresponding connector :SM02(8.0)B-BHS(JST) Pin no. symbol 1 VHIGH Power supply for lamp (High voltage side This is electrically opened. 3 VLOW Power supply for lamp ...
Page 9
Symbol Parameter Supply voltage LVDS Signals L Input voltage Ambient temperature [Note1]On-off conditions for supply voltage 0<t1 15ms 0<t2 10ms 0<t3 100ms 0<t4 1s 200ms<t5 Vcc-dip conditions 1) 2.5V Vcc td 10ms 2) Vcc<2.5V Vcc-dip conditions should ...
Page 10
Backlight driving The backlight system is an edge-lighting type with 2 CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. Parameter Symbol ...
Page 11
Timing characteristics of input signals 8-1. Timing characteristics (These are specified at the digital inputs/outputs of LVDS transmitter/receiver.) Data ENAB Sync C (Vertical timing) Item(symbol) Vsync cycle ( Blanking period Vsync pulse width (T ) ...
Page 12
Phase difference) Vsync Hsync Item(symbol) Hsync-Vsync Phase difference (T (Hsync-ENAB Phase difference) ENAB Hsync T HN Item Hsync-ENAB Phase difference (T 8-2 Display position Item Standards Horizontal rising edge of ENAB rising edge of Hsync Vertical rising edge of ...
Page 13
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray scale Scale Black - 0 0 ...
Page 14
Optical Characteristics Parameter Symbol Viewing Horizontal 21, 22 angle Vertical 11 range 12 Contrast ratio CRn CRo viewing angle Response Rise r time Decay d Chromaticity x of white y Luminance of white Y L1 White Uniformity W Viewing ...
Page 15
The contrast ratio is defined as the following. Luminance (brightness) with all pixels white Contrast Ratio (CR) = Luminance (brightness) with all ...
Page 16
Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 17
... Barcode Ｑｕａｎｔｉｔｙ： Barcode ユーザ品番 ： LQ104S1LG21 * 15-3 If any problem occurs in relation to the description of this specification , it shall be resolved through discussion with spirit of cooperation. Conditions Ta=70 240h Ta= -30 ...
Page 18
...
Page 19
...
Page 20
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...