LQ104V1DG62 Sharp Microelectronics, LQ104V1DG62 Datasheet - Page 15

• Manufacturer Part Number: LQ104V1DG62
• Description: TFT Displays & Accessories 10.4 640 x 480 246.5 x 179 x 12.5mm
• Manufacturer: Sharp Microelectronics

Specifications of LQ104V1DG62

• Attached Touch Screen: No
• Background Color: Normally White
• Diagonal: 10.4 in
• Operating Temperature Range: - 30 C to + 90 C
• Viewing Area (w X H): 211.2 mm x 158.4 mm
• Pixel Density: 640 x 480
• Module Size (w X H X T): 246.5 mm x 179.4 mm x 12.5 mm
• Backlighting: LED
• Lcd Display Type: VGA
• Display Mode: Transmissive
• Interface Type: Digital
• Viewing Area (h X W): 158.4mm X 211.2mm
• Supply Voltage: 5V
• External Depth: 12.5mm
• External Length / Height: 179.5mm
• External: RoHS Compliant
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Backlight Type: LED
• Backlighting Colour: White
• Pixel Pitch (h X W): 0.33mm X 0.33mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.Handling Precautions
w) The LED used for this product is very sensitive to the temperature. Luminance decreases rapidly when it is
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
n) Be careful of a back light lead not to pull by force at the time of the wiring to an converter, or line processing.
o) When install LCD modules in the cabinet, recommended torque value is “0.294 ± 0.02N ･ m (3.0 ± 0.2kgf ･ cm)”.
p) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye
q) Notice:Never dismantle the module , because it will cause failure.
t) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc.
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
i) Protection film is attached to the module surface to prevent it from being scratched .
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
m) When handling LCD modules and assembling them into cabinets, please be noted that long-term
r) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
s) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
Be sure to confirm it in the same condition as it is installed in your instrument.
Blow away dust on the polarizer with antistatic Ｎ
It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer.
When unavoidable, wipe off carefully with a cloth for wiping lenses.
warp or twist.
Handle with care.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
protective board over the LCD, be careful about the optical interface fringe etc. which degrades
display quality.
panel is used under such environment.
storage in the environment of oxidization or deoxidization gas and the use of such materials as
reagent,solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and
discoloration of the LCD modules.
or mouth by mistake.
If adjusted value is changed, the specification may not be satisfied.
Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
used for a long time under the environment of the high temperature.. Please consult our company when it is used under
the environment like the above mentioned.
when handling.Observe all other precautionary requirements in handling components.
2
blow. It is undesirable to wipe off because a polarizer is sensitive.
LD19659A-13