LQ035Q7DH06 Sharp Microelectronics, LQ035Q7DH06 Datasheet - Page 21

• Manufacturer Part Number: LQ035Q7DH06
• Description: TFT Displays & Accessories 3.5 240x320 225 nits w/Touch
• Manufacturer: Sharp Microelectronics

Specifications of LQ035Q7DH06

• Diagonal: 3.5 in
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 10 C
• Operating Temperature Range: - 10 C to + 70 C
• Product: Displays
• Touch Panel: Touch Panel
• Pixel Density: 240 x 320
• Module Size (w X H X T): 65 mm x 86.2 mm x 4 mm
• Backlighting: White Normally White
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

(13) Handling Precautions
13-1) Insertion and taking out of FPCs
13-2) Handling of FPCs
13-3) Installation of the module
13-4) Precautions when mounting
13-5) Others
(1) Be sure to turn off the power supply when inserting or disconnecting the FPC.
(2) Please insert FPC in the connector carefully so that the tension should not hang.
(3) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off
(4) Glass is used for the TFT-LCD panel. If it is dropped or bumped against a hard object, it may be broken.
(5) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when
(1) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
(2) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and the panel
(3) If the LCD breaks, don’t put internal liquid crystal into the mouth. Rinse it as soon as possible if it gets
(4) Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or
(5) Observe general precautions for all electronic components.
(6) VCOM must be adjusted on condition of your final product. No adjustment causes the deterioration for
(7) Static image should not be displayed more than 5 minutes in order to prevent from occurrence of
(8) If local pressure joins T/P surface for a long time, it will become the cause of generating of Newton’s ring.
(9) Since the front polarizer is easily damaged, pay attention not to scratch it. Blow away dust on the
(10) In case of attaching protective board over the LCD, be careful about the optical interface fringe etc.
On mounting the module, be sure to fix the module on the same plane. Taking care not to warp or twist
the module.
immediately.
Handle it with sufficient care.
handling. Observe all other precautionary requirements in handling components.
panel is used under such environment. The panel characteristic might be deteriorated and the display
fineness decrease when strong light is irradiated to the liquid crystal panel.
may be broken. Also, if it is kept at a temperature above the rated storage temperature, it becomes
isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it at room
temperature as much as possible.
inside your eye or mouth by mistake. When the liquid crystal sticks to the hands, feet and clothes, wash
it out immediately.
spots.
display quality.
afterimage.
polarizer with antistatic Ｎ2 blow. It is undesirable to wipe off because a polarizer is sensitive. It is
recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer.
When unavoidable, wipe off carefully with a cloth for wiping lenses.
which degrades display quality.
The FPC for LCD panel shall be bent only slit portion. The bending slit shall be bent uniformly on the
whole slit portion with bending radius larger than 0.6mm, and only inner side (back side of the module).
Don’t bend it outer side (display surface side).
Don’t give the FPCs too large force, for example, hanging the module with holding FPC.
LD-21909A-18