210304 WALTHER, 210304 Datasheet - Page 9

• Manufacturer Part Number: 210304
• Description: CONNECTOR, POWER ENTRY, PLUG, 16A
• Manufacturer: WALTHER

Specifications of 210304

• Gender: Plug
• Voltage Rating: 110VAC
• Current Rating: 16A
• Connector Mounting: Cable
• Connector Type: Standard Power Entry
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ELECTRICAL
Insulation Resistance
Dielectric Voltage Withstand
Ground Path Current
Endurance, Connect and Disconnect Cycles
Current Interrupting
Overload Test
(Power factor 0.75 - 0.80)
Temperature Rise
Resistance to Arcing
MECHANICAL
Mold Stress Relief
Humidity
Cable Secureness
Impact
Crushing
Withdrawal Force
Strength of Insulating
Base and Support
Polarization Integrity
ENVIRONMENTAL
Flammability
Ambient Temperature
Range
Resistance to Corrosion
Moisture Resistance
UV Resistance
IEC 309 PIN & SLEEVE DEVICES
IEC 309 PIN & SLEEVE DEVICES
subjected to splashing water in all directions (360°).
water for 10 minutes and immediately afterwards
V-2 or better per UL 94 or CSA 22.2 No. 0.6
Exposed plastic materials are UV stabilized.
highest point of the device being 2” (5cm)
Splashproof (IP44): Device is sprayed with
24 hours in water at a temp. of 25°C, the
40 lb (180 N) insertion force is applied.
Watertight (IP67): Device immersed for
8 times. The device is then conditioned
for 6 hours at -25°C and immediately
Matching devices will not mate so that
Minimum: -25°C (-13°F) with impact
150% of the rated current and 100%
polarization feature is removed and
500V for 1 min. Resistance 5M
Continuation of overload test for an
110% of specified tightening torque
the ground is energized, even when
Ferrous parts immersed for 10 min.
subjected to a repeated impact test.
Certified for current interrupting at
chloride at a temperature of 20°C.
250 lbs for 1 minute. The device is
of the rated voltage for 50 cycles.
32°C (89.6°F), 93% humidity for
(2300mm) length of flexible cord
Maximum 30° C rise at full rated
-25°C and immediately subjected
and dropped from 30” (760mm)
Tested for current interrupting at
in a 10% solution of ammonium
then conditioned for 6 hours at
full rated current and voltage.
A device is wired with a 90”
to a repeated crushing test.
70°C (158°F) for 7 hours.
Maximum: 90°C (194°F)
current (after overload).
below the water level.
additional 200 cycles.
7 days (168 hours).
on terminal screws.
3000V for 1 min.
•
•
PERFORMANCE SPECIFICATIONS
PERFORMANCE SPECIFICATIONS
See Table 1
See Table 2
See Table 3
See Table 4
TABLE 1
A test current that far exceeds the device rating, is passed through the
mating devices and grounding wires.
TABLE 2
The test sequence is conducted by using a no-load, followed by a load
sequence. The power factor of the load is 0.75 to 0.80.
TABLE 3
The flexible cord or cable is simultaneously twisted and pulled. Values for
the applied twisting torque and force of pull are shown in Table 3. In all
cases the cord displacement is less than 3/32 inches.
TABLE 4
The pressure exerted by mating contacts of a plug and connector must be
sufficient to prevent unintentional withdrawal during normal use. During
the test, any locking rings or retaining means are not to be engaged.
Amperes
Device
Rating
Amperes
100
Device
Rating
20
30
60
100
Amperes
Amperes
20
30
60
Device
Rating
Device
Rating
100
100
20
30
60
20
30
60
Certified
150
150
lb.
30
75
Force
Grounding Conductor
AWG
12
10
10
Load at Rated
8
Current and
Cycles with
Ground Path Current Test
Minimum Size
These products are Listed to applicable UL Standards
and requirements by Underwriters Laboratories Inc.
UL 1682
Withdrawal Forces Test
Voltage
133
333
667
667
Cable Secureness Test
5000
1000
1000
250
N
15
20
lb.
5
6
Endurance Test
•
•
Minimum Withdrawal Force
mm
ft-lb.
UL 1686
NORTH AMERICAN RATINGS
3.3
5.3
5.3
8.4
NORTH AMERICAN RATINGS
0.4
0.5
1.0
2.0
2
Torque
No-Load
Cycles
1000
1000
250
22
27
67
89
N
0
N•m
0.54
0.68
1.4
2.7
Seconds
Time,
4
4
4
4
Inches
3/32
3/32
3/32
3/32
Displacement
Time, Minutes
Maximum
Alternating
Alternating
Alternating
Sequence
Amperes
Current,
1
1
1
1
1180
-
7
470
750
750
Test
7
2.38
2.38
2.38
2.38
mm