CDB42L55 Cirrus Logic Inc, CDB42L55 Datasheet - Page 5

• Manufacturer Part Number: CDB42L55
• Description: Eval Bd Ultra Low Power Stereo Codec
• Manufacturer: Cirrus Logic Inc

Specifications of CDB42L55

• Main Purpose: Audio, CODEC
• Embedded: Yes, FPGA / CPLD
• Utilized Ic / Part: CS42L55
• Primary Attributes: 2 Stereo Analog Inputs, Stereo Line and Headphone Outputs, S/PDIF Transmitter and Receiver
• Secondary Attributes: GUI, USB, RS232, I2C Interfaces, USB or External or Battery Power Supply
• Product: Audio Modules
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 598-1506; CDB-42L55

DS773DB1
2 SYSTEM OVERVIEW
The CDB42L55 evaluation platform provides analog and digital interfaces to the CS42L55 and allows for external
DSP and I²C interconnects to the board. On-board peripherals are powered either from the USB connection or from
an external +5 V supply. On-board voltage regulators provide power to the digital and analog cores of the CS42L55.
The CDB42L55 is configured using Cirrus Logic’s Windows-compatible FlexGUI software to read/write to device
registers.
This section describes the various components on the CDB42L55 and how they are used with the CS42L55.
1 on page 4
the CS42L55.
dio signals.
tion of all stake headers and connectors, including the default factory settings of all jumpers.
provides typical performance plots. The CDB42L55 schematic and layout set is shown in
2.1
2.2
2.3
2.3.1
Control Port and Board Configuration
The CDB42L55 evaluation board must be programmed using the Windows compatible software (Cirrus Log-
ic FlexGUI) provided. This software allows the user to program the registers of all the programmable com-
ponents on the board using an I²C interface.
The GUI interfaces with an on-board micro controller through either the USB or the serial port connector.
For a detailed explanation on software controls, refer to
Alternatively, the I²C interface to the CS42L55 can be directly accessed through an I/O header (J109) to
accept external timing and data signals in a user application during system development.
Power
Power is supplied to the evaluation board through either the +5.0 V test points or the VBUS supply from the
USB. NOTE: The minimum current required for board operation is approximately 300 mA. It may therefore
be necessary to connect the CDB42L55 directly to the USB port on the PC as opposed to a hub or keyboard
port where the current might be limited.
Jumpers connect the CS42L55’s supplies to a low dropout regulated voltage of +1.8 V, +2.5 V or +3.3 V for
VL and +1.8 V or +2.5 V for VLDO, VA and VCP. A selection for a 1.8 V supply from a buck regulator is also
available, providing a more efficient means of evaluating the CS42L55’s performance when powered from
batteries (3 AAA battery connectors are available on the bottom side of the CDB).
For current measurement purposes only, a 1 Ω ohm series resistor is connected to each supply. The current
is easily calculated by measuring the voltage drop across this resistor. NOTE: The stake headers connected
in parallel with these resistors must be shunted with the supplied jumper during normal operation.
WARNING: Please refer to the CS42L55 data sheet for allowable voltage levels.
Digital Input
CS8416 S/PDIF Digital Audio Receiver
The CS8416 S/PDIF receiver converts an incoming S/PDIF data input stream into PCM data for the
CS42L55 (through the “Transmit” (Tx) Sample Rate Converter (SRC)).
A complete description of the CS8416
face can be found in the CS8416 data sheet.
Section 4 on page 10
is a simplified quick connect guide provided for user convenience and may be used to quickly configure
Section 3 on page 8
provides software configuration details.
describes some of the configurations available for transmitting and receiving au-
(Figure 38 on page
Section 4 on page 10.
26) and a discussion of the digital audio inter-
Section 5 on page 17
Figures 36
Section 6 on page 19
provides a descrip-
CDB42L55
through 46.
Section
5