AFCT-711XPDZ Avago Technologies US Inc., AFCT-711XPDZ Datasheet
AFCT-711XPDZ
Specifications of AFCT-711XPDZ
Related parts for AFCT-711XPDZ
AFCT-711XPDZ Summary of contents
Page 1
... AFCT-711XPDZ Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver Data Sheet Description The 1310 nm XFP transceiver is a high performance, cost effective module for serial optical data communications applications specified for signal rates of 9.95 Gb/s to 11.3 Gb/ compliant to XFP MSA Rev 4.5. The module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm ...
Page 2
... Installation The AFCT-711XPDZ is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. The attach heatsink is designed to clip on to the XFP cage without a module present. ...
Page 3
... RX_LOS can also be monitored via the two-wire serial interface (byte 110, bit 1). Functional Data I/O Avago Technologies’ AFCT-711XPDZ fiber-optic transceiv designed to accept industry standard electrical input differential signals. The transceiver provides AC-coupled, internally terminated data input and output interfaces. ...
Page 4
Table 1. Electrical Pin Definitions Pin Name Logic 1 GND Mod-Desel LVTTL-I 4 Interrupt LVTTL-O 5 TX_DIS LVTTL GND SCL LVTTL-I ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature (non-operating) Ambient Operating Temperature Relative Humidity Supply Voltage Low Speed Input Voltage [4] Recommended Operating Conditions Parameter Case Operating Temperature Supply Voltage Data Rate Transceiver Electrical Characteristics ( °C to +70 °C, ...
Page 6
Transmitter Electrical Input Characteristics ( °C to +70 ° 3.3 V ± 5 Parameter Differential Input Impedance Termination Mismatch Differential Input Amplitude Differential Input Return Loss Differential Input Return Loss Differential Input Return ...
Page 7
Transmitter Optical Characteristics 10 GbE/10GFC ( °C to +70 ° 3.3 V ± 5 Parameter Optical Output Power Average Optical Output Power Extinction Ratio Spectral Width - rms Center Wavelength Transmitter and dispersion ...
Page 8
Transmitter Optical Characteristics OC-192 SONET SR °C to +70 ° 3.3 V ± 5 Parameter Optical Output Power Extinction Ratio Spectral Width @ 20 dB Center Wavelength Side mode suppression ratio Output ...
Page 9
Transceiver Timing Characteristics ( °C to +70 ° 3.3 V ± 5 Parameter Symbol TX_DIS Assert Time t_off TX_DIS Negate Time t_on Time to initialize t_init Interrupt assert delay Interrupt_on Interrupt negate delay ...
Page 10
... Transmitted Average Optical Output Power Variations in average optical power are not expected under normal operation because the AFCT-711XPDZ uses a closed loop laser bias feedback circuit to maintain constant optical power over time at a given temperature. This circuit compensates for normal laser parametric variations due to changing transceiver operating points ...
Page 11
Clip Heat Sink Cage Assembly Figure 4. XFP Assembly Drawing 11 Host Board EMI Gasket (not shown) Bezel Module Connector ...
Page 12
Mechanical Specifications Package Dimensions Figure 5a. Module Drawing Figure 5b. Module Drawing 12 ...
Page 13
Figure 6. XFP host board mechanical layout 13 ...
Page 14
... Application Support An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-711XPDZ. Please contact your local Field Sales representative for availability and ordering details. Regulatory Compliance The transceiver Regulatory Compliance performance is provided in Table figure of merit to assist the designer. The overall equipment design will determine the certification level ...
Page 15
... It may also result in improper operation of the AFCT- 711XPDZ circuitry, and possible overstress of the laser source. Device degradation or product failure may result. Connection of the AFCT-711XPDZ to a non-approved optical source, operating above the recommended absolute maximum conditions may be considered an act of modifying or manufacturing a laser product. The ...