ACPL-W70L-560E Avago Technologies US Inc., ACPL-W70L-560E Datasheet - Page 5

• Manufacturer Part Number: ACPL-W70L-560E
• Description: Stretch Singles Pb-free TR VDE
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-W70L-560E

• Voltage - Isolation: 5000Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 15MBd
• Propagation Delay High - Low @ If: 23ns @ 6mA
• Current - Dc Forward (if): 10mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount
• Package / Case: 6-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

All Avago Technologies data sheets report the creepage
and clearance inherent to the optocoupler component it-
self. These dimensions are needed as a starting point for
the equipment designer when determining the circuit
insulation requirements. However, once mounted on a
printed circuit board, minimum creepage and clearance
requirements must be met as specified for individual
equipment standards. For creepage, the shortest distance
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics*
Note:
*
** Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section IEC/EN/
These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured by
means of protective circuits. The surface mount classification is Class A in accordance with CECC 00802.
5
Parameter
Minimum External Air
Gap (Clearance)
Minimum External
Tracking (Creepage)
Minimum Internal Plastic
Gap (Internal Clearance)
Tracking Resistance
(Comparative Tracking Index)
Isolation Group
Description
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b
V
Input to Output Test Voltage, Method a
V
Highest Allowable Overvoltage (Transient Overvoltage t
Safety-limiting values – maximum values allowed in the event of a failure, also see Figure 2.
Insulation Resistance at T
IORM
IORM
Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Surface mount classification is class A in accordance with CECCOO802.
DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles.
for rated mains voltage 150 V
for rated mains voltage 300 V
for rated mains voltage 450 V
for rated mains voltage 600 V
for rated mains voltage 1000 V
Case Temperature
Input Current
Output Power
x 1.875=V
x 1.5=V
PR,
PR,
Type and Sample Test, t
100% Production Test with t
S
, V
IO
= 500 V
rms
rms
rms
rms
rms
Symbol
L(I01)
L(I02)
CTI
**
**
m
=60 sec, Partial discharge < 5 pC
m
=1 sec, Partial discharge < 5 pC
Value
8.0
8.0
0.08
≥175
IIIa
ini
= 10 sec)
path along the surface of a printed circuit board between
the solder fillets of the input and output leads must be
considered.
There are recommended techniques such as grooves
and ribs which may be used on a printed circuit board to
achieve desired creepage and clearances. Creepage and
clearance distances will also change depending on factors
such as pollution degree and insulation level.
Units
mm
mm
mm
Volts
Conditions
Measured from input terminals to output
terminals, shortest distance through air.
Measured from input terminals to output ter-
minals, shortest distance path along body.
Insulation thickness between emitter and
detector; also known as distance through
insulation.
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
Symbol
V
V
V
V
T
I
P
R
S, INPUT
S
S, OUTPUT
IO
IORM
PR
PR
IOTM
Option 060 Units
I – IV
I - III
I – III
I – III
I – III
55/105/21
2
1140
2137
1710
8000
175
230
600
>109
V
V
V
V
°C
mA
mW
:
peak
peak
peak
peak