GP1UX511QS Sharp Microelectronics, GP1UX511QS Datasheet - Page 4

• Manufacturer Part Number: GP1UX511QS
• Description: IR RECEIVER, 5M, THROUGH HOLE
• Manufacturer: Sharp Microelectronics

Specifications of GP1UX511QS

• Supply Voltage Range: 4.5V To 5.5V
• Operating Temperature Range: -10°C To +70°C
• Length/height, External: 8.8mm
• External Width: 5.5mm
• External Depth: 5.3mm
• Carrier Frequency: 38kHz
• Supply Current: 500µA
• Transmission Distance: 8.5 m
• High Level Pulse Width: 1200 us
• Low Level Pulse Width: 1000 us
• Minimum High Level Output Voltage: 4 V
• Operating Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 10 C
• Output Current Max: 1.5mA
• Operating Temperature Max: 70°C
• Rohs Compliant: Yes
• Sensing Distance: 8.5m
• B.p.f. Center Frequency: 38.0kHz
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 600µA
• Orientation: Side View
• Mounting Type: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

8. External Circuit Examples (Mount the outer parts as near the unit as possible).
5. Do not push the light detector surface (photodiode) from outside.
6. To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
3. Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
4. Unnecessary force shoud not be applied to terminal.
7. Since conductive thermo plasticity is used in 2nd mold regin,please be careful not to come in contact with PCB land
■ Precautions for Operation
1. When this infrared remote control detecting unit shall be adopted for wireless remote control, please use the following signal format .
(NEC code,RC-6code etc.)
2. Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics, operating conditions of
・ON signal time T
・Total duty ratio D
Care must be taken not to touch the light detector surface.
The circuit constant is a example. It is difference from mounting equipment. Please select it by your mounting equipment.
This device has a transistor as protection element between V
Please be carefully not to apply exceeding the absolute maximum ratings of applying voltage and continuous high voltage spike
noise because there is cases that transistor will be short by secondary breakdown generally. In order to do difficultly, Please add CR
filter(47Ω(1/10W), 10μF or more)such as external circuit example above near V
If it should be dirty, wipe off such dust and refuse with soft cloth so as to prevent scratch. In case some solvents are required, use
methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the
function, fading of markings such as the part number.
In setting R
pattern.
light emitting device and the characteristics of the light detecting unit.
In case the signal format of total duty and/or ON/OFF signal time dosen`t meet the conditions noted above, there is a
case that reception distance much reduces or output dose not appear.
1
and C
ON：
1
t
, use suitable values after considering under the real condition
(Emitting time t
t
1
200μs or more.
GND
V
V
CC
OUT
Σ
N=1
n
t
2
N
/ Transmitting time for 1 block T) : 40% or less.
C
Transmitting time for 1 block:T
O
+
t
3
D
t
=(
N=1
Σ
n
R
t
1
N
/T) ×100 (%)
CC
and GND to improve anti-static electricity proof.
4
GND
V
V
e
O
(Circuit parameters)
R
C
1=
1=
47Ω±5%
47μF
CC
T
.
t
ON
n
GP1UX51QS Series
Sheet No.: OP06012