LQ035Q1DH01 Sharp Microelectronics, LQ035Q1DH01 Datasheet
LQ035Q1DH01
Specifications of LQ035Q1DH01
Related parts for LQ035Q1DH01
LQ035Q1DH01 Summary of contents
Page 1
...
Page 2
...
Page 3
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 4
... Applicable Scope This specification is applicable to TFT-LCD Module “LQ035Q1DH01”. 2. General Description This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver IC, Input FPC, a back light unit and a touch panel. Graphics and texts can be displayed on a 320 × RGB × 240 dots panel with about 262k colors by supplying 18bit data signals (6bit × ...
Page 5
Input Terminal Names and Functions Recommendation CN [HIROSE] FH26G-67S-0.3SHBW(05) or [KYOCERA ELCO] 00 6281 067 2X2 829 + Pin No. Symbol I/O 1 LED_C (-) - 2 LED_A(+) - 3 DGND1 - ...
Page 6
Pin No. Symbol I ...
Page 7
Note 4) Stabilization and charge sharing Capacitors LCY-W-07201 Page ...
Page 8
Absolute Maximum Ratings Item Input voltage Logic I/O power supply voltage Analog power supply voltage Temperature for storage Temperature for operation LED input electric current LED electricity consumption Note 1) RESB, SHUT, CSB, SDI, SCK, DEN, B5~B0, G5~G0, R5~R0, ...
Page 9
Electrical Characteristics 6-1. TFT LCD Panel Driving Item DC voltage Logic I/O power supply DC Current DC voltage Analog power supply DC Current Permissive input Ripple voltage High Logic Input Voltage Low Logic input Current Note ...
Page 10
Register Setting Reg. # R01 h R02 h R03 h R0B h R0C h R0D h R0E h R0F h R16 h R17 h R1E h R2E h R30 h R31 h R32 h R33 h R34 h R35 ...
Page 11
Note 1) LCY-W-07201 Page ...
Page 12
Note 2) 6-3. Back light driving The back light system has 7 LEDs [NSSW020B] Parameter Symbol Rated Voltage Rated Current Power consumption Min. Typ 22 448 L LCY-W-07201 Page 10 of ...
Page 13
Timing characteristics of input signals 7-1. Pixel Clock Timing Pixel Clock Timing LCY-W-07201 Page ...
Page 14
Data Transaction Timing in Normal Operating Mode (262k color) LCY-W-07201 Page ...
Page 15
Synchronization Signals Timing in Power Save Mode (8 color) LCY-W-07201 Page ...
Page 16
V Output against SHUT & RESB GH LCY-W-07201 Page ...
Page 17
Power Up Sequence LCY-W-07201 Page ...
Page 18
Power Down Sequence LCY-W-07201 Page ...
Page 19
SPI Interface Timing Diagram & Transaction Example (9 bit) LCY-W-07201 Page ...
Page 20
Input Data Signals and Display Position on the screen Please refer to Input Terminal Names and Functions LCY-W-07201 Page ...
Page 21
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray R0 R1 Scale Scale LSB Black 0 0 Blue 0 0 Green 0 0 Cyan 0 0 Red 1 1 Magenta 1 1 Yellow ...
Page 22
Optical Characteristics Parameter Symbol Viewing Horizontal angle range (Without Vertical Wide View) Contrast ratio CR Response Rise Time Decay Chromaticity of White X Luminance of white Uniformity * The optical characteristics measurements are operated under a stable luminescence (I ...
Page 23
Note 1 Definitions of viewing angle range 12 Note 2 Definition of contrast ratio The contrast ratio is defined as the following C ontrast ratio (CR) Note 3 Definition of response time The response time is defined as the following ...
Page 24
Note 5 Definition of Uniformity Minimum Brightness Uniformity Maximum Brightness The brightness should be measured on the 9-point as shown in the right figure. Note 6 This shall be measured on the 9-point as shown in the right figure. Summation ...
Page 25
Touch panel characteristics Parameter Input voltage Resistor between terminals(XL-XR) Resistor between terminals(YU-YD) Line linearity(X direction) Line linearity(Y direction) Insuration resistance Minimum tension for detecting Note) For use of finger input 11. Handling of modules 11-1. Inserting the FPC into ...
Page 26
Mounting on display and housing bezel (1) In all cases, the T/P should be supported from the backside of the Plastic. (2) Do not to use an adhesive-tape to bond it on the front of T/P and hang it ...
Page 27
If water dropped, etc. remains stuck on the polarizer for a long time apt to get discolored or cause stains. Wipe it immediately glass substrate is used for the TFT-LCD panel ...
Page 28
Reliability test items No. Test item 1 High temperature storage test Low temperature storage test 2 High temperature 3 & high humidity operation test 4 High temperature operation test 5 Low temperature operation test Vibration test 6 (non- operating) ...
Page 29
... Tray (The number of Module) Electrification prevention bag Carton weight (120 modules): Approx. 9.8kg 15. Lot No. marking The lot No. will be indicated on individual labels. The location is as shown Indication Label LQ035Q1DH01 Model No + Parts code (A~H) 16. LCD module packing carton quantity 1 575×360×225 (mm) 12 ...
Page 30
Others 1 Disassembling the module can cause permanent damage and you should be strictly avoided. 2 Please be careful that you don’t keep the screen displayed fixed pattern image for a long time, since retention may occur ...
Page 31
...