D4NH3132H Omron, D4NH3132H Datasheet - Page 3

• Manufacturer Part Number: D4NH3132H
• Description: LIMIT SWITCH, SPDT-1NO/1NC
• Manufacturer: Omron
• Series: D4NHr

Specifications of D4NH3132H

• Contact Voltage Ac Max: 240V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 2.5A
• Switch Terminals: Screw
• Contact Configuration: SPDT-1NO / 1NC
• Circuitry: SPDT-1NO/1NC
• Lead Free Status / RoHS Status: na

Specifications
Standards and EC Directives
Conforms to the following EC Directives:
Certified Standards
* Certification for CSA C22.2 No. 14 is authorized by the UL mark.
Characteristics
Note: 1. The above values are initial values.
*1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing properties are sufficient for
*2. The durability is for an ambient temperature of 5 to 35°C and an ambient humidity of 40% to 70%. For more details, consult your
*3. Do not pass the 3 A, 250 VAC load through more than 2 circuits.
*4. This value will vary with the switching frequency, environment, and reliability level. Confirm that correct operation is possible with the actual
• Machinery Directive
• Low Voltage Directive
• EN50047
• EN60204-1
• EN1088
• GS-ET-15
Certification body
Degree of protection *1
Durability *2
Operating speed
Operating frequency
Contact resistance
Minimum applicable load *4
Rated insulation voltage (U
Rated frequency
Protection against electric shock
Pollution degree (operating environment)
Impulse withstand
voltage
(EN60947-5-1)
Insulation resistance
Contact gap
Vibration resistance
Shock resistance
Conditional short-circuit current
Conventional free air thermal current (I
Ambient operating temperature
Ambient operating humidity
Weight
the operating conditions and environment beforehand. Although the switch box is protected from dust or water penetration, do not use the
D4NH in places where foreign material such as dust, dirt, oil, water, or chemicals may enter through the head. Otherwise, accelerated wear,
Switch damage, or malfunctioning may occur.
OMRON representative.
load beforehand.
CCC (CQC)
TÜV SÜD
2. Once the contacts have been used to switch a load, however, they cannot be used to switch smaller loads. The contact surfaces will
UL *
become rough once they have been used and contact reliability for smaller loads may be reduced.
EN60947-5-1
(certified direct opening)
UL508, CSA C22.2
No.14
GB14048.5
Mechanical
Electrical
Between terminals of same
polarity
Between terminals of
different polarity
Between each terminal and
non-current carrying
metallic parts
Malfunction
Destruction
Malfunction
Standard
i
)
th
)
2004010305105973
Ask your OMRON
representative for
certified models.
information on
File No.
E76675
IP67 (EN60947-5-1)
1,000,000 operations min.
500,000 operations min. (3 A resistive load at 250 VAC) *3
300,000 operations min. (10 A resistive load at 250 VAC)
2 to 360°/s
30 operations/minute max.
25 mΩ max.
1 mA resistive load at 5 VDC (N-level reference value)
300 V
50/60 Hz
Class II (double insulation)
3 (EN60947-5-1)
2.5 kV
4 kV
6 kV
100 MΩ min.
2 × 2 mm min.
10 to 55 Hz, 0.75 mm single amplitude
1,000 m/s
300 m/s
100 A (EN60947-5-1)
10 A (EN60947-5-1)
−30 to 70°C (with no icing)
95% max.
Approx. 87 g (D4NH-1AAS)
Approx. 97 g (D4NH-1ABC)
2
min.
2
min.
Certified Standard Ratings
TÜV (EN60947-5-1)
Note: Use a 10 A fuse type gI or gG that conforms to IEC60269 as a
UL/CSA (UL508, CSA C22.2 No. 14)
A300
Q300
Item
Rated operating current (I
Rated operating voltage (U
120 VAC
240 VAC
125 VDC
250 VDC
voltage
voltage
Rated
Rated
short-circuit protection device. This fuse is not built into the
Switch.
Utilization category
Carry current
Carry current
2.5 A
10 A
e
)
e
)
Make
Make
0.55
0.27
60
30
Current (A)
Current (A)
AC-15
240 V
3 A
Break
Break
0.55
0.27
6
3
Volt-amperes (VA)
Volt-amperes (VA)
Make
7,200
Make
69
DC-13
0.27 A
250 V
D4NH
Break
Break
720
69
3